In some circumstances (old LSA flushed but not acknowledged and not
removed) origination of a new LSA may wrongly triggers LSA collision
code. The patch fixes that.
Thanks to Asbjorn Mikkelsen for the bugreport and @mdelagueronniere
for the original patch.
Extend 'next hop keep' and 'next hop self' options to have boolean values
(enabled / disabled) and also values 'ibgp'/ 'ebgp' to restrict it to
routes received from IBGP / EBGP. This allows to have it enabled by
default in some cases, matches features of other implementations, and
allows to handle some strange cases like EBGP border router with 'next
hop self' also doing IBGP route reflecting.
Change default of 'next hop keep' to enabled for route servers, and
'ibgp' for route reflectors.
Update documentation for these options.
When route is exported to regular EBGP, local ASN should be prepended to
AS_PATH. When route is propagated by route server (between RS-marked
EBGP peers), it should not change AS_PATH. Question is what to do in
other cases (from non-RS EBGP, IBGP, or locally originated to RS EBGP).
In 1.6.x, we did not prepend ASN in non-RS EBGP or IBGP to RS EBGP, but
we prepended in local to RS EBGP.
In 2.0.x, we changed that so only RS-EBGP to RS-EBGP is not prepended.
We received some negative responses (thanks to heisenbug and Alexander
Zubkov), we decided to change it back. One reason is that it is simple
to modify the AS_PATH by filters, but not possible to un-modify
changes done by BGP itself. Also, as 1.6.x behavior was not really
consistent, the final behavior is that ASN is never prepended when
exported to RS EBGP, like to IBGP.
Note that i do not express an opinion about whether such configurations
are even reasonable.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
When a new channel is found during reconfiguration, do force restart
of the protocol, like with any other un-reconfigurable change.
The old behavior was that the new channel was added but remained in down
state, even if the protocol was up, so a manual protocol restart was
often necessary.
In the future this should be improved such that a reconfigurable
channel addition (e.g. direct) is accepted and channel is started,
while an un-reconfigurable addition forces protocol restart.
Fix crash during reconfiguration of OSPF config with vlinks. When vlink
is reconfigured, a generic iface-reconfiguration code is used, which in
one place supposes that it is running on a regular iface.
Thanks to Cybertinus for a bugreport.
Once upon a time, far far away, there were the old Bird developers
discussing what direction of route flow shall be called import and
export. They decided to say "import to protocol" and "export to table"
when speaking about a protocol. When speaking about a table, they
spoke about "importing to table" and "exporting to protocol".
The latter terminology was adopted in configuration, then also the
bird CLI in commit ea2ae6dd0 started to use it (in year 2009). Now
it's 2018 and the terminology is the latter. Import is from protocol to
table, export is from table to protocol. Anyway, there was still an
import_control hook which executed right before route export.
One thing is funny. There are two commits in April 1999 with just two
minutes between them. The older announces the final settlement
on config terminology, the newer uses the other definition. Let's see
their commit messages as the git-log tool shows them (the newer first):
commit 9e0e485e50
Author: Martin Mares <mj@ucw.cz>
Date: Mon Apr 5 20:17:59 1999 +0000
Added some new protocol hooks (look at the comments for better explanation):
make_tmp_attrs Convert inline attributes to ea_list
store_tmp_attrs Convert ea_list to inline attributes
import_control Pre-import decisions
commit 5056c559c4
Author: Martin Mares <mj@ucw.cz>
Date: Mon Apr 5 20:15:31 1999 +0000
Changed syntax of attaching filters to protocols to hopefully the final
version:
EXPORT <filter-spec> for outbound routes (i.e., those announced
by BIRD to the rest of the world).
IMPORT <filter-spec> for inbound routes (i.e., those imported
by BIRD from the rest of the world).
where <filter-spec> is one of:
ALL pass all routes
NONE drop all routes
FILTER <name> use named filter
FILTER { <filter> } use explicitly defined filter
For all protocols, the default is IMPORT ALL, EXPORT NONE. This includes
the kernel protocol, so that you need to add EXPORT ALL to get the previous
configuration of kernel syncer (as usually, see doc/bird.conf.example for
a bird.conf example :)).
Let's say RIP to this almost 19-years-old inconsistency. For now, if you
import a route, it is always from protocol to table. If you export a
route, it is always from table to protocol.
And they lived happily ever after.
Modify protocols to use preferred address change notification instead on
depending on hard-reset of interfaces in that case, and remove hard-reset
in that case. This avoids issue when e.g. IPv6 protocol restarts
interface when IPv4 preferred address changed (as hard-reset is
unavoidable and common for whole iface).
The patch also fixes a bug when removing last address does not send
preferred address change notification.
The new MRT protocol is responsible for periodic RIB table dumps in the
MRT format (RFC 6396). Also the existing code for BGP4MP MRT dumps is
refactored and splitted between BGP to MRT protocols, will be more
integrated into MRT in the future.
Example:
protocol mrt {
table "*";
filename "%N_%F_%T.mrt";
period 60;
}
It is partially based on the old MRT code from Pavel Tvrdik.
Missing argument in MTU change trace message can crash bird when MTU
change happens and trace messages are active.
Thanks to Alexander Velkov for the bugreport.
no more warnings
No more warnings over me
And while it is being compiled all the log is black and white
Release BIRD now and then let it flee
(use the melody of well-known Oh Freedom!)
We currently cannot assing local labels, but we can still be LSP egress
router. Therefore when we announce labeled route with local next-hop, we
should announce implicit-NULL label instead of rejecting it completely.
RFC 3107 was bit vague with regard to labeled withdrawals, RFC 8277
clarified that. The old code was incompatible with some implementations,
namely with Juniper.
Thanks to Vadim Fedorenko for the original patch.
In case of missing IPv4 next hop, we should skip such routes
on transmit and ignore such routes on receive.
Thanks to Julian Schuh for the bugreport and Toke Hoiland-Jorgensen
for the original patch.
This is a fundamental change of an original (1999) concept of route
processing inside BIRD. During import/export, there was a temporary
ea_list created which was to be used instead of the another one inside
the route itself.
This led to some confusion, quirks, and strange filter code that handled
extended route attributes. Dropping it now.
The protocol interface has changed in an uniform way -- the
`struct ea_list *attrs` argument has been removed from store_tmp_attrs(),
import_control(), rt_notify() and get_route_info().
During route export, the receiving protocol often initialized route
metrics to default value in its import_control hook before export filter
was executed. This is inconsistent with the expectation that an export
filter would process the same route as one in the routing table and it
breaks setting these metrics before (e.g. for static routes directly in
static protocol).
The patch removes the initialization of route metrics in import_control
hook, the default values are already handled in rt_notify hook called
after export filters.
The patch also changed the behavior of OSPF to keep metrics when a route
is reannounced between OSPF instances (to be consistent with other
protocols) and the behavior when both ospf_metric1 and ospf_metric2
are specified (to have more expected behavior).
When a Babel node restarts, it loses its sequence number, which can cause
its routes to be rejected by peers until the state is cleared out by other
nodes in the network (which can take on the order of minutes).
There are two ways to fix this: Having stable storage to keep the sequence
number across restarts, or picking a different router ID each time.
This implements the latter, by introducing a new option that will cause
BIRD to randomize a high 32 bits of router ID every time it starts up.
This avoids the problem at the cost of not having stable router IDs in
the network.
Thanks to Toke Hoiland-Jorgensen for the patch.
The router ID being assigned to routes was a uint, which discards the
upper 32 bits. This also has the nice side effect of echoing the wrong
router ID back to other routers.
Thanks to Toke Hoiland-Jorgensen for the patch.
This patch adds support for source-specific routing to the Babel protocol.
It changes the protocol to support both NET_IP6 and NET_IP6_SADR channels
for IPv6 addresses. If only a NET_IP6 channel is configured,
source-specific updates are ignored. Otherwise, non-source-specific
routes are simply treated as source-specific routes with SADR prefix 0.
Thanks to Toke Hoiland-Jorgensen for the original patch.
Minor changes by Ondrej Santiago Zajicek.
Several changes and bugfixes in Babel, namely:
- Exported route parameters stored directly in route table entry
- Exported non-babel routes no longer stored in per-entry route list
- Route update, selection and retraction simplified and fixed
- Route feasibility is evalualated per update and stored with route
- Unreachable route handling fixed, based on hold interval
- Added 'show babel routes' command
Overall, it fixes some issues with proper propagation of triggered
updates, making Babel convergence after topology change almost
instant.
Also fix several minor bugs and add 'limit' option for k-out-of-j
link sensing strategy. Change default from 8-of-16 to 12-of-16.
Change IHU expiry factor from 1.5 to 3.5 (as in RFC 6126).
The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
RFC6126bis introduces a flags field for the Hello TLV, and adds a unicast flag
that is used to signify that a hello was sent as unicast. This adds parsing of
the flags field and ignores such unicast hellos, which preserves compatibility
until we can add a proper implementation of the unicast hello mechanism.
Thanks to Toke Hoiland-Jorgensen for the patch.
The TTL check must be done after instance ID dispatch to avoid warnings
when a physical iface is shared by multiple instances and some use TTL
security and some not.
In such case, next hop has to be taken from Link-LSA like in broadcast
case, not from neighbor source address like in other PtP cases.
Also add some checks, comments and code cleanup.
OSPFv3-AF can handle multiple topologies of diferent address families
(IPv4, IPv6, both unicast and multicast) using separate instances
distinguished by instance ID ranges.
The patch implements Default Router Preferences and More-Specific Routes
(RFC 4191) for RAdv protocol, allowing to announce router preference and
more specific routes in router advertisements. Routes can be exported to
RAdv like to regular routing protocols.
Some cleanups, bugfixes and other changes done by Ondrej Zajicek.
The patch implements BGP Administrative Shutdown Communication (RFC 8203)
allowing BGP operators to pass messages related to BGP session
administrative shutdown/restart. It handles both transmit and receive of
shutdown messages. Messages are logged and may be displayed by show
protocol all command.
Thanks to Job Snijders for the basic patch.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
Keep a cache of all the relevant prefixes we send out. When a prefix
appears, insert it into the cache. If it dies, keep it there for a
while, marked as dead.
Send out the dead prefixes with zero lifetime.
Adapt the naming conventions to be a bit closer to the other protocols.
proto_radv -> radv_proto
struct radv_proto *ra -> struct radv_proto *p
struct proto *p -> struct proto *P
Adapt the naming conventions to be a bit closer to the other protocols.
proto_radv -> radv_proto
struct radv_proto *ra -> struct radv_proto *p
struct proto *p -> struct proto *P
Add proper support for per-nexthop onlink flag in routes to handle next
hop addresses that are not covered by interface IP ranges. Supported by
kernel and static protocols.
Thanks to Vincent Bernat for the idea.
The subtlv parsing code was doing byte-based arithmetic with non-void pointers,
causing it to read beyond the end of the packet.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
RFC6126bis formally introduces sub-TLVs to the Babel protocol, including
mandatory sub-TLVs. This adds support for parsing sub-TLVs to the Babel
protocol and skips TLVs that contain mandatory sub-TLVs, as per the spec.
For details, see section 4.4 of
https://tools.ietf.org/html/draft-ietf-babel-rfc6126bis-02
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
Previously, the Babel protocol would never use prefix compression on outgoing
updates (but would parse it on incoming ones). This adds compression of IPv6
addresses of outgoing updates.
The compression only works to the extent that the FIB is walked in lexicographic
order; i.e. a prefix is only compressed if it shares bytes with the previous
prefix in the same packet.
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
This adds support for dual-stack v4/v6 operation to the Babel protocol.
Routing messages will be exchanged over IPv6, but IPv4 routes can be
carried in the messages being exchanged. This matches how the reference
Babel implementation (babeld) works.
The nexthop address for v4 can be configured per interface, and will
default to the first available IPv4 address on the given interface. For
symmetry, a configuration option to configure the IPv6 nexthop address
is also added.
Thanks to Toke Høiland-Jørgensen <toke@toke.dk> for the patch.
Covers IPv4/VPNv4 routes with IPv6 next hop (RFC 5549), IPv6 routes with
IPv4 next hop (RFC 4798) and VPNv6 routes with IPv4 next hop (RFC 4659).
Unfortunately it also makes next hop hooks more messy.
Each BGP channel now could have two IGP tables, one for IPv4 next hops,
the other for IPv6 next hops.
Basic support for SAFI 4 and 128 (MPLS labeled IP and VPN) for IPv4 and
IPv6. Should work for route reflector, but does not properly handle
originating routes with next hop self.
Based on patches from Jan Matejka.
When a BGP session with ADD_PATH is restarted and the neighbor do not
announce ADD_PATH capability during reconnect, the accept_ra_types is
still set to RA_ANY.
Thanks to Lennert Buytenhek for the bugreport
The patch fixes several bugs introduced in previous changes, simplifies
the protocol by handing routes uniformly, introduces asynchronous route
processing to avoid issues with separate notifications for each next-hop
in ECMP routes, and makes reconfiguration faster by avoiding quadratic
complexity.
During reconfiguration, old and new filter expressions in static routes
are compared using i_same() function. When filter expressions contain
function calls, it is necessary that old filter expressions are the
second argument in i_same(), as it is internally modified by i_same().
Otherwise pointers to old (and freed) data appear in the config
structure.
Thanks to Lennert Buytenhek for tracking and reporting the bug.
Dropped struct mpnh and mpnh_*()
Now struct nexthop exists, nexthop_*(), and also included struct nexthop
into struct rta.
Also converted RTD_DEVICE and RTD_ROUTER to RTD_UNICAST. If it is needed
to distinguish between these two cases, RTD_DEVICE is equivalent to
IPA_ZERO(a->nh.gw), RTD_ROUTER is then IPA_NONZERO(a->nh.gw).
From now on, we also explicitely want C99 compatible compiler. We assume
that this 20-year norm should be known almost everywhere.
The variable nfa is not cleaned before each loop iteration and can have
a wrong value of nfa.nhs_reuse from the previous step.
Thanks to Bernardo Figueiredo for the bugreport and analysis.
Stubnet nodes in OSPF FIB were removed during rt_sync(), but the pointer
remained in top_hash_entry.nf, so net-summary LSA origination was
confused, reported 'LSA ID collision' and net-summary LSAs were not
originated properly.
Thanks to Naveen Chowdary Yerramneni for bugreport and analysis.
Prefix and bucket tables are initialized when entering established state
but not explicitly freed when leaving it (that is handled by protocol
restart). With graceful restart, BGP may enter and leave established
state multiple times without hard protocol restart causing memory leak.
Commit 3c09af41... changed behavior of int_set_add() from prepend to
append, which makes more sense for community list, but prepend must be
used for cluster list. Add int_set_prepend() and use it in cluster list
handling code.
- Unit Testing Framework (BirdTest)
- Integration of BirdTest into the BIRD build system
- Tests for several BIRD modules
Based on squashed Pavel Tvrdik's int-test branch, updated for
current int-new branch.
Implement BFD authentication (part of RFC 5880). Supports plaintext
passwords and cryptographic MD5 / SHA-1 authentication.
Based on former commit from Pavel Tvrdik
Add support for large communities (draft-ietf-idr-large-community),
96bit alternative to RFC 1997 communities.
Thanks to Matt Griswold for the original patch.
It is possible that sockets_add() are called between sockets_prepare()
and sockets_fire() during poll loop in birdloop_main(), so we need to
use loop->poll_fd.used instead of loop->sock_num to find the last field.
An interface reconfiguration may change both the hello and update
intervals. An update interval change is immediately put into effect,
while a hello interval change is not. This also updates the hello
interval immediately (if the new interval is shorter than the old one),
and sends a hello to notify peers of the change.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
We do not need to maintain feasibility distances for our own router
ID (we ignore the updates anyway). Not doing so makes the routes be
garbage collected sooner when export filters change.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
When a route becomes infeasible it should not be kept as selected; this
is forbidden by section 3.6 of the RFC and prevents subsequent updates
from the same router ID from replacing it.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
This makes BIRD send a wildcard retraction on all interfaces before
shutting down and right after starting up. This helps ensure that
neighbours will discard the announced routes as soon as possible,
rather than only after the normal timeout procedures.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
An update with wildcard AE and infinite metric should be treated as a
global retraction of all prefixes announced by that neighbour, per
section 4.4.9 of the RFC. In addition, router ID and seqno in retraction
updates should be ignored. This reworks the handling of retractions and
adjusts the parser to handle all this correctly.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Intervals are carried as 16-bit centisecond values, but kept internally
in 16-bit second values, which causes a potential for overflow. This adds
some checks to make sure this does not happen.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Although RFC 4271 does not forbid empty path segments, they are useless
and some implementations consider them invalid. It is clarified in RFC 7606,
specifying that AS_PATH with empty segment is considered malformed.
Also removed the lib-dir merging with sysdep. Updated #include's
accordingly.
Fixed make doc on recent Debian together with moving generated doc into
objdir.
Moved Makefile.in into root dir
Retired all.o and birdlib.a
Linking the final binaries directly from all the .o files.
This patch implements the IPv6 subset of the Babel routing protocol.
Based on the patch from Toke Hoiland-Jorgensen, with some heavy
modifications and bugfixes.
Thanks to Toke Hoiland-Jorgensen for the original patch.
Add code for manipulation with TCP-MD5 keys in the IPsec SA/SP database
at FreeBSD systems. Now, BGP MD5 authentication (RFC 2385) keys are
handled automatically on both Linux and FreeBSD.
Based on patches from Pavel Tvrdik.
Many protocols do almost the same when creating a rte_update request
before calling rte_update2(). This commit should simplify the protocol
side of the route-creation routine.
In BIRD, RX has lower priority than TX with the exception of RX from
control socket. The patch replaces heuristic based on socket type with
explicit mark and uses it for both control socket and BGP session waiting
to be established.
This should avoid an issue when during heavy load, outgoing connection
could connect (TX event), send open, but then failed to receive OPEN /
establish in time, not sending notifications between and therefore
got hold timer expired error from the neighbor immediately after it
finally established the connection.
After restart, LSAs locally originated by the previous instance are
received from neighbors. They are installed to LSA db and flushed. If
export of a route triggers origination of a new external LSA before flush
of the received one is complete, the check in ospf_originate_lsa() causes
origination to fail (because en->nf is NULL for the old LSA and non-NULL
for the new LSA). The patch fixes this by updating the en->nf for LSAs
being flushed (as is already done for empty ones). Generally, en->nf
field deserves some better description in the code.
Thanks to Jigar Mehta for analyzing the problem.
When a BGP session was established by an outgoing connection with
Graceful Restart behavior negotiated, a pending incoming connection in
OpenSent state, and another incoming connection was received, then the
outgoing connection (and whole BGP session) was closed, but the old
incoming connection was just overwritten by the new one. That later
caused a crash when the hold timer from the old connection fired.
The patch adds support for channels, structures connecting protocols and
tables and handling most interactions between them. The documentation is
missing yet.
Explicit setting of AF_INET(6|) in IP socket creation. BFD set to listen
on v6, without setting the V6ONLY flag to catch both v4 and v6 traffic.
Squashing and minor changes by Ondrej Santiago Zajicek
New data types net_addr and variants (in lib/net.h) describing
network addresses (prefix/pxlen). Modifications of FIB structures
to handle these data types and changing everything to use these
data types instead of prefix/pxlen pairs where possible.
The commit is WiP, some protocols are not yet updated (BGP, Kernel),
and the code contains some temporary scaffolding.
Comments are welcome.
The new RIP implementation fixes plenty of old bugs and also adds support
for many new features: ECMP support, link state support, BFD support,
configurable split horizon and more. Most options are now per-interface.
The patch adds suport for specifying route attributes together with
static routes, e.g.:
route 10.1.1.0/24 via 10.0.0.1 { krt_advmss = 1200; ospf_metric1 = 100; };
New LSA checksumming code separates generic Fletcher-16 and OSPF-specific
code and avoids back and forth endianity conversions, making it much more
readable and also several times faster.
Prior to this patch, BIRD validates the OSPF LSA checksum by calculating
a new checksum and comparing it with the checksum in the header. Due to
the specifics of the Fletcher checksum used in OSPF, this is not
necessarily correct as the checkbytes in the header may be calculated via
a different means and end up with a different value that is nonetheless
still correct.
The documented means of validating the checksum as specified in RFC 905
B.4 is to calculate c0 and c1 from the unchanged contents of the packet,
which must result in a zero value to be considered valid.
Thanks to Chris Boot for the patch.
Under some circumstances and heavy load, TX could be postponed
until the session fails with hold timer expired.
Thanks to Javor Kliachev for making the bug reproductible.
Permit specifying neighbor address, AS number and port independently.
Add 'interface' parameter for specifying interface for link-local
sessions independently.
Thanks to Alexander V. Chernikov for the original patch.
