Missing translation from BGP attribute ID to eattr ID in bgp_unset_attr()
broke automatic removal of bgp_med during export to EBGP peers.
Thanks to Edward Sun for the bugreport.
Even though the free bind option is primarily meant to alleviate problems
with addresses assigned too late, it's also possible to use BIRD with AnyIP
configuration, assigning whole ranges to the machine. Therefore free bind
allows also to create an outbound connection from specific address even though
such address is not assigned.
The babel protocol normally sends all its messages as multicast packets,
but the protocol specification allows most messages to be sent as either
unicast or multicast, and the two can be mixed freely. In particular, the
babeld implementation can be configured to unicast updates to all peers
instead of sending them as unicast.
Daniel discovered that this can cause problems with the packet counter
checks in the MAC extension due to packet reordering. This happens on WiFi
networks where clients have power save enabled (which is quite common in
infrastructure networks): in this case, the access point will buffer all
multicast traffic and only send it out along with its beacons, leading to a
maximum buffering in default Linux-based access point configuration of up
to 200 ms.
This means that a Babel sender that mixes unicast and multicast messages
can have the unicast messages overtake the multicast messages because of
this buffering; when authentication is enabled, this causes the receiver to
discard the multicast message when it does arrive because it now has a
packet counter value less than the unicast message that arrived before it.
Daniel observed that this happens frequently enough that Babel ceases to
work entirely when runner over a WiFi network.
The issue has been described in draft-ietf-babel-mac-relaxed, which is
currently pending RFC publication. That also describes two mitigation
mechanisms: Keeping separate PC counters for unicast and multicast, and
using a reorder window for PC values. This patch implements the former as
that is the simplest, and resolves the particular issue seen on WiFi.
Thanks to Daniel Gröber for the bugreport.
Minor changes from committer.
The patch implements an IPv4 via IPv6 extension (RFC 9229) to the Babel
routing protocol (RFC 8966) that allows annoncing routes to an IPv4
prefix with an IPv6 next hop, which makes it possible for IPv4 traffic
to flow through interfaces that have not been assigned an IPv4 address.
The implementation is compatible with the current Babeld version.
Thanks to Toke Høiland-Jørgensen for early review on this work.
Minor changes from committer.
When creating a new babel_source object we initialise the seqno to 0. The
caller will update the source object with the right metric and seqno value,
for both newly created and old source objects. However if we initialise the
source object seqno to 0 that may actually turn out to be a valid (higher)
seqno than the one in the routing table, because of seqno wrapping. In this
case the source metric will not be set properly, which breaks feasibility
tracking for subsequent updates.
To fix this, add a new initial_seqno argument to babel_get_source() which
is used when allocating a new object, and set that to the seqno value of
the update we're sending.
Thanks to Juliusz Chroboczek for the bugreport.
Juliusz noticed there were a couple of places we were doing straight
inequality comparisons of seqnos in Babel. This is wrong because seqnos can
wrap: so we need to use the modulo-64k comparison function for these cases
as well.
Introduce a strict-inequality version of the modulo-comparison for this
purpose.
For active sessions, ignore received packets with zero local id and
mismatched remote id. That forces a session timeout instead of an
immediate session restart. It makes BFD sessions more resilient to
packet spoofing.
Thanks to André Grüneberg for the suggestion.
Protocols receive if_notify() announcements that are filtered according
to their VRF setting, but during reconfiguration, they access iface_list
directly and forgot to check VRF setting here, which leads to all
interfaces be addedd.
Fix this issue for Babel, OSPF, RAdv and RIP protocols.
Thanks to Marcel Menzel for the bugreport.
Some of these new BGP role keywords use generic names that collides with
user-defined symbols. Allow them to be redefined. Also remove duplicit
keyword definition for 'prefer'.
During backporting attribute changes from 3.0-branch, some internal
attributes (RIP iface and Babel seqno) leaked to 'show route all' output.
Allow protocols to hide specific attributes with GA_HIDDEN value.
Thanks to Nigel Kukard for the bugreport.
There were some confusion about validity and usage of pflags, which
caused incorrect usage after some flags from (now removed) protocol-
specific area were moved to pflags.
We state that pflags:
- Are secondary data used by protocol-specific hooks
- Can be changed on an existing route (in contrast to copy-on-write
for primary data)
- Are irrelevant for propagation (not propagated when changed)
- Are specific to a routing table (not propagated by pipe)
The patch did these fixes:
- Do not compare pflags in rte_same(), as they may keep cached values
like BGP_REF_STALE, causing spurious propagation.
- Initialize pflags to zero in rte_get_temp(), avoid initialization in
protocol code, fixing at least two forgotten initializations (krt
and one case in babel).
- Improve documentation about pflags
The seqno request retransmission handling was tracking the destination
that a forwarded request was being sent to and always retransmitting to
that same destination. This is unnecessary because we only need to
retransmit requests we originate ourselves, not those we forward on
behalf of others; in fact retransmitting on behalf of others can lead to
exponential multiplication of requests, which would be bad.
So rework the seqno request tracking so that instead of storing the
destination of a request, we just track whether it was a request that we
forwarded on behalf of another node, or if it was a request we originated
ourselves. Forwarded requests are not retransmitted, they are only used
for duplicate suppression, and for triggering an update when satisfied.
If we end up originating a request that we previously forwarded, we
"upgrade" the old request and restart the retransmit counter.
One complication with this is that requests sent in response to unfeasible
updates (section 3.8.2.2 of the RFC) have to be sent as unicast to a
particular peer. However, we don't really need to retransmit those as
there's no starvation when sending such a request; so we just change
such requests to be one-off unicast requests that are not subject to
retransmission or duplicate suppression. This is the same behaviour as
babeld has for such requests.
Minor changes from committer.
The effective keepalive time now scales relative to the negotiated
hold time, to maintain proportion between the keepalive time and the
hold time. This avoids issues when both keepalive and hold times
were configured, the hold time was negotiated to a smaller value,
but the keepalive time stayed the same.
Add new options 'min hold time' and 'min keepalive time', which reject
session attempts with too small hold time.
Improve validation of config options an their documentation.
Thanks to Alexander Zubkov and Sergei Goriunov for suggestions.
Add BGP channel option 'next hop prefer global' that modifies BGP
recursive next hop resolution to use global next hop IPv6 address instead
of link-local next hop IPv6 address for immediate next hop of received
routes.
- When next hop is reset to local IP, we should remove BGP label stack,
as it is related to original next hop
- BGP next hop or immediate next hop from one VRF should not be passed
to another VRF, as they are different IP namespaces
In principle, the channel list is a list of parent struct proto and can
contain general structures of type struct channel, That is useful e.g.
for adding MPLS channels to BGP.
Implement BGP roles as described in RFC 9234. It is a mechanism for
route leak prevention and automatic route filtering based on common BGP
topology relationships. It defines role capability (controlled by 'local
role' option) and OTC route attribute, which is used for automatic route
filtering and leak detection.
Minor changes done by commiter.
When f_line is done, we have to pop the stack frame. The old code just
removed nominal number of args/vars. Change it to use stored ventry value
modified by number of returned values. This allows to allocate variables
on a stack frame during execution of f_lines instead of just at start.
But we need to know the number of returned values for a f_line. It is 1
for term, 0 for cmd. Store that to f_line during linearization.
Passing protocol to preexport was in fact a historical relic from the
old times when channels weren't a thing. Refactoring that to match
current extensibility needs.
The Babel seqno request code keeps track of which seqno requests are
outstanding for a neighbour by putting them onto a per-neighbour list. When
reusing a seqno request, it will try to remove this node, but if the seqno
request in question was a multicast request with no neighbour attached this
will result in a crash because it tries to remove a list node that wasn't
added to any list.
Fix this by making the list remove conditional. Also fix neighbor removal
which were changing seqno requests to multicast ones instead of removing
them.
Fixes: ebd5751cde ("Babel: Seqno requests are properly decoupled from
neighbors when the underlying interface disappears").
Based on the patch from Toke Høiland-Jørgensen <toke@toke.dk>,
bug reported by Stefan Haller <stefan.haller@stha.de>, thanks.
The prefix hash table in BGP used the same hash function as the rtable.
When a batch of routes are exported during feed/flush to the BGP, they
all have similar hash values, so they are all crowded in a few slots in
the BGP prefix table (which is much smaller - around the size of the
batch - and uses higher bits from hash values), making it much slower due
to excessive collisions. Use a different hash function to avoid this.
Also, increase the batch size to fill 4k BGP packets and increase minimum
BGP bucket and prefix hash sizes to avoid back and forth resizing during
flushes.
This leads to order of magnitude faster flushes (on my test data).
When shutting down a Babel instance we send a wildcard retraction to make
sure all peers can quickly switch to other route origins. Add another small
optimisation borrowed from babeld: sending a Hello message (along with the
retraction) with a very low interval.
This will cause neighbours to modify their expiry timers for the node's
state to quickly time it out, thus conserving resources in the network.
The interface pointer was improperly converted to u32 and back. Fixing
this by explicitly allocating an adata structure for it. It's not so
memory efficient, we'll optimize this later.
Add BFD protocol option 'strict bind' to use separate listening socket
for each BFD interface bound to its address instead of using shared
listening sockets.
It is too cryptic to flush tmp_linpool in these cases and we don't want
anybody in the future to break this code by adding an allocation
somewhere which should persist over that flush.
Saving and restoring linpool state is safer.
