multicast abilities depending on definedness of symbols and use hard-wired
system-dependent configuration defines instead.
Please test whereever you can.
but the core routines are there and seem to be working.
o lib/ipv6.[ch] written
o Lexical analyser recognizes IPv6 addresses and when in IPv6
mode, treats pure IPv4 addresses as router IDs.
o Router ID must be configured manually on IPv6 systems.
o Added SCOPE_ORGANIZATION for org-scoped IPv6 multicasts.
o Fixed few places where ipa_(hton|ntoh) was called as a function
returning converted address.
The changes are just too extensive for lazy me to list them
there, but see the comment at the top of sysdep/unix/krt.c.
The code got a bit more ifdeffy than I'd like, though.
Also fixed a bunch of FIXME's and added a couple of others. :)
reside, so that you can easily switch between 2.0 and 2.2 ones.
Check existence of <linux/rtnetlink.h> for linux-22 configs to make sure
we're using the correct set of includes.
addresses per interface (needed for example for IPv6 support).
Visible changes:
o struct iface now contains a list of all interface addresses (represented
by struct ifa), iface->addr points to the primary address (if any).
o Interface has IF_UP set iff it's up and it has a primary address.
o IF_UP is now independent on IF_IGNORED (i.e., you need to test IF_IGNORED
in the protocols; I've added this, but please check).
o The if_notify_change hook has been simplified (only one interface pointer
etc.).
o Introduced a ifa_notify_change hook. (For now, only the Direct protocol
does use it -- it's wise to just listen to device routes in all other
protocols.)
o Removed IF_CHANGE_FLAGS notifier flag (it was meaningless anyway).
o Updated all the code except netlink (I'll look at it tomorrow) to match
the new semantics (please look at your code to ensure I did it right).
Things to fix:
o Netlink.
o Make krt-iface interpret "eth0:1"-type aliases as secondary addresses.
o Nothing is configured automatically. You _need_ to specify
the kernel syncer in config file in order to get it started.
o Syncing has been split to route syncer (protocol "Kernel") and
interface syncer (protocol "Device"), device routes are generated
by protocol "Direct" (now can exist in multiple instances, so that
it will be possible to feed different device routes to different
routing tables once multiple tables get supported).
See doc/bird.conf.example for a living example of these shiny features.
The new kernel syncer is cleanly split between generic UNIX module
and OS dependent submodules:
- krt.c (the generic part)
- krt-iface (low-level functions for interface handling)
- krt-scan (low-level functions for routing table scanning)
- krt-set (low-level functions for setting of kernel routes)
krt-set and krt-iface are common for all BSD-like Unices, krt-scan is heavily
system dependent (most Unices require /dev/kmem parsing, Linux uses /proc),
Netlink substitues all three modules.
We expect each UNIX port supports kernel routing table scanning, kernel
interface table scanning, kernel route manipulation and possibly also
asynchronous event notifications (new route, interface state change;
not implemented yet) and build the KRT protocol on the top of these
primitive operations.
of various callbacks.
Events are just another resource type objects (thus automatically freed
and unlinked when the protocol using them shuts down). Each event can
be linked in at most one event list. For most purposes, just use the
global event list handled by the following functions:
ev_schedule Schedule event to be called at the next event
scheduling point. If the event was already
scheduled, it's just re-linked to the end of the list.
ev_postpone Postpone an already scheduled event, so that it
won't get called. Postponed events can be scheduled
again by ev_schedule().
You can also create custom event lists to build your own synchronization
primitives. Just use:
ev_init_list to initialize an event list
ev_enqueue to schedule event on specified event list
ev_postpone works as well for custom lists
ev_run_list to run all events on your custom list
ev_run to run a specific event and dequeue it
#define L_DEBUG "\001" /* Debugging messages */
#define L_INFO "\002" /* Informational messages */
#define L_WARN "\003" /* Warnings */
#define L_ERR "\004" /* Errors */
#define L_AUTH "\005" /* Authorization failed etc. */
#define L_FATAL "\006" /* Fatal errors */
#define L_TRACE "\002" /* Protocol tracing */
#define L_INFO "\003" /* Informational messages */
#define L_REMOTE "\004" /* Remote protocol errors */
#define L_WARN "\004" /* Local warnings */
#define L_ERR "\005" /* Local errors */
#define L_AUTH "\006" /* Authorization failed etc. */
#define L_FATAL "\007" /* Fatal errors */
#define L_BUG "\010" /* BIRD bugs */
Introduced bug() which is like die(), but with level L_BUG. Protocols
should _never_ call die() as it should be used only during initialization
and on irrecoverable catastrophic events like out of memory.
Also introduced ASSERT() which behaves like normal assert(), but it calls
bug() when assertion fails. When !defined(DEBUGGING), it gets ignored.
o Interface syncing is now a part of krt and it can have configurable
parameters. Actually, the only one is scan rate now :)
o Kernel routing table syncing is now synchronized with interface
syncing (we need the most recent version of the interface list
to prevent lots of routes to non-existent destinations from
appearing). Instead of its own timer, we just check if it's
route scan time after each iface list scan.
o Syncing of device routes implemented.
o CONFIG_AUTO_ROUTES should control syncing of automatic device routes.
o Rewrote krt_remove_route() to really remove routes :)
o Better diagnostics.
o Fixed a couple of bugs.
