On large configurations, too many threads would spawn with one thread
per loop. Therefore, threads may now run multiple loops at once. The
thread count is configurable and may be changed during run. All threads
are spawned on startup.
This change helps with memory bloating. BIRD filters need large
temporary memory blocks to store their stack and also memory management
keeps its hot page storage per-thread.
Known bugs:
* Thread autobalancing is not yet implemented.
* Low latency loops are executed together with standard loops.
If no channel is flushing, table prune doesn't walk over routes in nets
and also doesn't walk over importing channel lists. This helps to
alleviate the memory caching burdens a lot.
Add static route attribute to set onlink flag for route next hop. Can be
used to build a dynamically routed IP-in-IP overlay network. Usage:
ifname = "tunl0";
onlink = true;
gw = bgp_next_hop;
The import table does not work reliably together with re-evaluation of
routes due to recursive next hops or flowspec validation. We will at
least document that here, as import tables are completely redesigned and
this issue is fixed in BIRD 3.x branch.
The effective keepalive time now scales relative to the negotiated
hold time, to maintain proportion between the keepalive time and the
hold time. This avoids issues when both keepalive and hold times
were configured, the hold time was negotiated to a smaller value,
but the keepalive time stayed the same.
Add new options 'min hold time' and 'min keepalive time', which reject
session attempts with too small hold time.
Improve validation of config options an their documentation.
Thanks to Alexander Zubkov and Sergei Goriunov for suggestions.
BIRD keeps a previous (old) configuration for the purpose of undo. The
existing code frees it after a new configuration is successfully parsed
during reconfiguration. That causes memory usage spikes as there are
temporarily three configurations (old, current, and new). The patch
changes it to free the old one before parsing the new one (as user
already requested a new config). The disadvantage is that undo is
not available after failed reconfiguration.
Add BGP channel option 'next hop prefer global' that modifies BGP
recursive next hop resolution to use global next hop IPv6 address instead
of link-local next hop IPv6 address for immediate next hop of received
routes.
By this, the requesting channels do the timers in their own loops,
avoiding unnecessary synchronization when the central timer went off.
This is of course less effective for now, yet it allows to easily
implement selective reloads in future.
These routines detect the export congestion (as defined by configurable
thresholds) and propagate the state to readers. There are no readers for
now, they will be added in following commits.
Implement BGP roles as described in RFC 9234. It is a mechanism for
route leak prevention and automatic route filtering based on common BGP
topology relationships. It defines role capability (controlled by 'local
role' option) and OTC route attribute, which is used for automatic route
filtering and leak detection.
Minor changes done by commiter.
For loops allow to iterate over elements in compound data like BGP paths
or community lists. The syntax is:
for [ <type> ] <variable> in <expr> do <command-body>
Allow variable declarations mixed with code, also in nested blocks with
proper scoping, and with variable initializers. E.g:
function fn(int a)
{
int b;
int c = 10;
if a > 20 then
{
b = 30;
int d = c * 2;
print a, b, c, d;
}
string s = "Hello";
}
Added an option for export filter to allow for prefiltering based on the
prefix. Routes outside the given prefix are completely ignored. Config
is simple:
export in <net> <filter>;
Use timer (configurable as 'gc period') to schedule routing table
GC/pruning to ensure that prune is done on time but not too often.
Randomize GC timers to avoid concentration of GC events from different
tables in one loop cycle.
Fix a bug that caused minimum inter-GC interval be 5 us instead of 5 s.
Make default 'gc period' adaptive based on number of routing tables,
from 10 s for small setups to 600 s for large ones.
In marge multi-table RS setup, the patch improved time of flushing
a downed peer from 20-30 min to <2 min and removed 40s latencies.
The route scope attribute was used for simple user route marking. As
there is a better tool for this (custom attributes), the old and limited
way can be dropped.
Add BFD protocol option 'strict bind' to use separate listening socket
for each BFD interface bound to its address instead of using shared
listening sockets.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
Add option 'netlink rx buffer' to specify netlink socket receive buffer
size. Uses SO_RCVBUFFORCE, so it can override rmem_max limit.
Thanks to Trisha Biswas and Michal for the original patches.
We can also quite simply allocate bigger blocks. Anyway, we need these
blocks to be aligned to their size which needs one mmap() two times
bigger and then two munmap()s returning the unaligned parts.
The user can specify -B <N> on startup when <N> is the exponent of 2,
setting the block size to 2^N. On most systems, N is 12, anyway if you
know that your configuration is going to eat gigabytes of RAM, you are
almost forced to raise your block size as you may easily get into memory
fragmentation issues or you have to raise your maximum mapping count,
e.g. "sysctl vm.max_map_count=(number)".
Some cleanups and bugfixes to the previous patch, including:
- Fix rate limiting in index mismatch check
- Fix missing BABEL_AUTH_INDEX_LEN in auth_tx_overhead computation
- Fix missing auth_tx_overhead recalculation during reconfiguration
- Fix pseudoheader construction in babel_auth_sign() (sport vs fport)
- Fix typecasts for ptrdiffs in log messages
- Make auth log messages similar to corresponding RIP/OSPF ones
- Change auth log messages for events that happen during regular
operation to debug messages
- Switch meaning of babel_auth_check*() functions for consistency
with corresponding RIP/OSPF ones
- Remove requirement for min/max key length, only those required by
given MAC code are enforced
This implements support for MAC authentication in the Babel protocol, as
specified by RFC 8967. The implementation seeks to follow the RFC as close
as possible, with the only deliberate deviation being the addition of
support for all the HMAC algorithms already supported by Bird, as well as
the Blake2b variant of the Blake algorithm.
For description of applicability, assumptions and security properties,
see RFC 8967 sections 1.1 and 1.2.
Add support for specifying a password in hexadecimal format, The result
is the same whether a password is specified as a quoted string or a
hex-encoded byte string, this just makes it more convenient to input
high-entropy byte strings as MAC keys.
The Babel MAC authentication RFC recommends implementing Blake2s as one of
the supported algorithms. In order to achieve do this, add the blake2b and
blake2s hash functions for MAC authentication. The hashing function
implementations are the reference implementations from blake2.net.
The Blake2 algorithms allow specifying an arbitrary output size, and the
Babel MAC spec says to implement Blake2s with 128-bit output. To satisfy
this, we add two different variants of each of the algorithms, one using
the default size (256 bits for Blake2s, 512 bits for Blake2b), and one
using half the default output size.
Update to BIRD coding style done by committer.
For numeric operators, comma is used for disjunction in expressions like
"10, 20, 30..40". But for bitmask operators, comma is used for
conjunction in a way that does not really make much sense. Use always
explicit logical operators (&& and ||) to connect bitmask operators.
Thanks to Matt Corallo for the bugreport.
Add support to set or read outgoing MPLS labels using filters. Currently
this supports the addition of one label per route for the first next hop.
Minor changes by committer.
BIRD uses hacked LinuxDocTools for building documentation, keeping some
parts locally and using remaining parts from system-installed one. This
setup breaks when LinuxDocTools makes some internal changes and is hard
to keep consistent.
Just include full LinuxDocTools code (both hacked and unmodified parts)
to avoid consistency issues. Note that we still need some binaries from
LinuxDocTools, so it still needs to be installed to build documentation.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
Add 'weight' route attribute that allows to get and set ECMP weight of
nexthops. Similar to 'gw' attribute, it is limited to the first nexthop,
but it is useful for handling BGP multipath, where an ECMP route is
merged from multiple regular routes.
Add support for proper handling of multiple routes with the same network
to the static protocol. Routes are distinguished by internal index, which
is assigned automatically (sequentially for routes within each network).
Having different route preference or igp_metric attribute is optional.
Add 'ignore max length' option to RPKI protocol, which ignores received
max length in ROA records and instead uses max value (32 or 128). This
may be useful for implementing loose RPKI check for blackholes.
This issue has a long history. In 2012, we changed data field for
unnumbered PtP links from iface id (specified by RFC) to IP address based
on reports of bugs in Quagga that required it, and we used out-of-band
information to distinquish unnumberred PtPs with the same local IP
address.
Then with OSPF graceful restart implementation, we found that we can no
longer use out-of-band information, and we need to use only LSAdb info
for routing table calculation, but i forgot to finish handling of this
case, so multiple unnumbered PtPs with the same local IP addresses were
broken.
Considering that even recent Mikrotik RouterOS has broken next hop
calculation that depends on IP address in PtP link data field, we
cannot just switch back to the iface id for unnumbered PtP links.
The patch makes two changes: First, it goes back to use out-of-band
(position) info for distinguishing local interfaces in SPF when graceful
restart is not enabled, while still uses LSAdb-only approach for SPF
calculation when graceful restart is enabled.
Second, it adds OSPF interface option 'ptp address', which controls
whether IP address or iface id is used in data field. It is enabled
by default except for unnumbered PtP links with enabled graceful
restart.
Thanks to Kenth Eriksson for the bugreport and Joakim Tjernlund for
suggestions.
There is nothing in RFCs specifying that id 0 is not allowed. Some
implementations does not support it, while some other use key id 0 by
default. We allow it but start with key id 1 by default.
Thanks to Kenth Eriksson for the bugreport.
Implement regex-like '+' operator in BGP path masks to match previous
path mask item multiple times. This is useful as ASNs may appear
multiple times in paths due to path prepending for traffic engineering
purposes.
