Introduced by 13ef5e53dd, the CLI was not
properly cleaned up when the command finished, causing BIRD to not parse
any other command after "show route".
For BGP LLGR purposes, there was an API allowing a protocol to directly
modify their stale routes in table before flushing them. This API was
called by the table prune routine which violates the future locking
requirements.
Instead of this, BGP now requests a special route export and reimports
these routes into the table, allowing for asynchronous execution without
locking the table on export.
Until now, we were marking routes as REF_STALE and REF_DISCARD to
cleanup old routes after route refresh. This needed a synchronous route
table walk at both beginning and the end of route refresh routine,
marking the routes by the flags.
We avoid these walks by using a stale counter. Every route contains:
u8 stale_cycle;
Every import hook contains:
u8 stale_set;
u8 stale_valid;
u8 stale_pruned;
u8 stale_pruning;
In base_state, stale_set == stale_valid == stale_pruned == stale_pruning
and all routes' stale_cycle also have the same value.
The route refresh looks like follows:
+ ----------- + --------- + ----------- + ------------- + ------------ +
| | stale_set | stale_valid | stale_pruning | stale_pruned |
| Base | x | x | x | x |
| Begin | x+1 | x | x | x |
... now routes are being inserted with stale_cycle == (x+1)
| End | x+1 | x+1 | x | x |
... now table pruning routine is scheduled
| Prune begin | x+1 | x+1 | x+1 | x |
... now routes with stale_cycle not between stale_set and stale_valid
are deleted
| Prune end | x+1 | x+1 | x+1 | x+1 |
+ ----------- + --------- + ----------- + ------------- + ------------ +
The pruning routine is asynchronous and may have high latency in
high-load environments. Therefore, multiple route refresh requests may
happen before the pruning routine starts, leading to this situation:
| Prune begin | x+k | x+k | x -> x+k | x |
... or even
| Prune begin | x+k+1 | x+k | x -> x+k | x |
... if the prune event starts while another route refresh is running.
In such a case, the pruning routine still deletes routes not fitting
between stale_set and and stale_valid, effectively pruning the remnants
of all unpruned route refreshes from before:
| Prune end | x+k | x+k | x+k | x+k |
In extremely rare cases, there may happen too many route refreshes
before any route prune routine finishes. If the difference between
stale_valid and stale_pruned becomes more than 128 when requesting for
another route refresh, the routine walks the table synchronously and
resets all the stale values to a base state, while logging a warning.
The learnt routes are now pushed all into the connected table, not only
the best one. This shouldn't do any damage in well managed setups, yet
it should be noted that it is a change of behavior.
If anybody misses a feature which they implemented by misusing this
internal learn table, let us know, we'll consider implementing it in a
better way.
Until now, if export table was enabled, Nest was storing exactly the
route before rt_notify() was called on it. This was quite sloppy and
spooky and it also wasn't reflecting the changes BGP does before
sending. And as BGP is storing the routes to be sent anyway, we are
simply keeping the already-sent routes in there to better rule out
unneeded reexports.
Some of the route attributes (IGP metric, preference) make no sense in
BGP, therefore these will be probably replaced by something sensible.
Also the nexthop shown in the short output is the BGP nexthop.
It's now possible to pause iteration through hash. This requires
struct hash_iterator to be allocated somewhere handy.
The iteration itself is surrounded by HASH_WALK_ITER and
HASH_WALK_ITER_END. Call HASH_WALK_ITER_PUT to ask for pausing; it may
still do some more iterations until it comes to a suitable pausing
point. The iterator must be initalized to an empty structure. No cleanup
is needed if iteration is abandoned inbetween.
For loops allow to iterate over elements in compound data like BGP paths
or community lists. The syntax is:
for [ <type> ] <variable> in <expr> do <command-body>
Allow variable declarations mixed with code, also in nested blocks with
proper scoping, and with variable initializers. E.g:
function fn(int a)
{
int b;
int c = 10;
if a > 20 then
{
b = 30;
int d = c * 2;
print a, b, c, d;
}
string s = "Hello";
}
When f_line is done, we have to pop the stack frame. The old code just
removed nominal number of args/vars. Change it to use stored ventry value
modified by number of returned values. This allows to allocate variables
on a stack frame during execution of f_lines instead of just at start.
But we need to know the number of returned values for a f_line. It is 1
for term, 0 for cmd. Store that to f_line during linearization.
When a new variable used the same name as an existing symbol in an outer
scope, then offset number was defined based on a scope of the existing
symbol ($3) instead of a scope of the new symbol (sym_). That can lead
to two variables sharing the same memory slot.
Direct recursion almost worked, just crashed on function signature check.
Split function parsing such that function signature is saved before
function body is processed. Recursive calls are marked so they can be
avoided during f_same() and similar code walking.
Also, include tower of hanoi solver as a test case.
Add literal for empty set [], which works both for tree-based sets
and prefix sets by using existing constant promotion mechanism.
Minor changes by committer.
All instructions with a return value (i.e. expressions, ones with
non-zero outval, third argument in INST()) should declare their return
type. Check that automatically by M4 macros.
Set outval of FI_RETURN to 0. The instruction adds one value to stack,
but syntactically it is a statement, not an expression.
Add fake return type declaration to FI_CALL, otherwise the automatic
check would fail builds.
Pass instructions of function call arguments as vararg arguments to
FI_CALL instruction constructor and move necessary magic from parser
code to interpreter / instruction code.
Passing protocol to preexport was in fact a historical relic from the
old times when channels weren't a thing. Refactoring that to match
current extensibility needs.
In the multithreaded environment, it is not supposed that anybody
traverses the routing table as the CLI show-route was doing. Now the
routing table traversal is gone and CLI won't hold the table locked
while computing filters.
Added an option for export filter to allow for prefiltering based on the
prefix. Routes outside the given prefix are completely ignored. Config
is simple:
export in <net> <filter>;
