Had to fix route source locking inside BGP export table as we need to
keep the route sources properly allocated until even last BGP pending
update is sent out, therefore the export table printout is accurate.
For BGP LLGR purposes, there was an API allowing a protocol to directly
modify their stale routes in table before flushing them. This API was
called by the table prune routine which violates the future locking
requirements.
Instead of this, BGP now requests a special route export and reimports
these routes into the table, allowing for asynchronous execution without
locking the table on export.
Implement BGP roles as described in RFC 9234. It is a mechanism for
route leak prevention and automatic route filtering based on common BGP
topology relationships. It defines role capability (controlled by 'local
role' option) and OTC route attribute, which is used for automatic route
filtering and leak detection.
Minor changes done by commiter.
Until now, if export table was enabled, Nest was storing exactly the
route before rt_notify() was called on it. This was quite sloppy and
spooky and it also wasn't reflecting the changes BGP does before
sending. And as BGP is storing the routes to be sent anyway, we are
simply keeping the already-sent routes in there to better rule out
unneeded reexports.
Some of the route attributes (IGP metric, preference) make no sense in
BGP, therefore these will be probably replaced by something sensible.
Also the nexthop shown in the short output is the BGP nexthop.
Passing protocol to preexport was in fact a historical relic from the
old times when channels weren't a thing. Refactoring that to match
current extensibility needs.
There were quite a lot of conflicts in flowspec validation code which
ultimately led to some code being a bit rewritten, not only adapted from
this or that branch, yet it is still in a limit of a merge.
For now, all route attributes are stored as eattrs in ea_list. This
should make route manipulation easier and it also allows for a layered
approach of route attributes where updates from filters will be stored
as an overlay over the previous version.
As there is either a nexthop or another destination specification
(or othing in case of ROAs and Flowspec), it may be merged together.
This code is somehow quirky and should be replaced in future by better
implementation of nexthop.
Also flowspec validation result has its own attribute now as it doesn't
have anything to do with route nexthop.
Changes in internal API:
* Every route attribute must be defined as struct ea_class somewhere.
* Registration of route attributes known at startup must be done by
ea_register_init() from protocol build functions.
* Every attribute has now its symbol registered in a global symbol table
defined as SYM_ATTRIBUTE
* All attribute ID's are dynamically allocated.
* Attribute value custom formatting hook is defined in the ea_class.
* Attribute names are the same for display and filters, always prefixed
by protocol name.
Also added some unit testing code for filters with route attributes.
This commit removes the EAF_TYPE_* namespace completely and also for
route attributes, filter-based types T_* are used. This simplifies
fetching and setting route attributes from filters.
Also, there is now union bval which serves as an universal value holder
instead of private unions held separately by eattr and filter code.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
Most error messages in attribute processing are in rx/decode step and
these use L_REMOTE log class. But there are few that are in tx/export
step and these should use L_ERR log class.
Use tx-specific macro (REJECT()) in tx/export code and rename field
err_withdraw to err_reject in struct bgp_export_state to ensure that
appropriate error reporting macros are called in proper contexts.
This commit prevents use-after-free of routes belonging to protocols
which have been already destroyed, delaying also all the protocols'
shutdown until all of their routes have been finally propagated through
all the pipes down to the appropriate exports.
The use-after-free was somehow hypothetic yet theoretically possible in
rare conditions, when one BGP protocol authors a lot of routes and the
user deletes that protocol by reconfiguring in the same time as next hop
update is requested, causing rte_better() to be called on a
not-yet-pruned network prefix while the owner protocol has been already
freed.
In parallel execution environments, this would happen an inter-thread
use-after-free, causing possible heisenbugs or other nasty problems.
* internal tables are now more standalone, having their own import and
export hooks
* route refresh/reload uses stale counter instead of stale flag,
allowing to drop walking the table at the beginning
* route modify (by BGP LLGR) is now done by a special refeed hook,
reimporting the modified routes directly without filters
Routes are now allocated only when they are just to be inserted to the
table. Updating a route needs a locally allocated route structure.
Ownership of the attributes is also now not transfered from protocols to
tables and vice versa but just borrowed which should be easier to handle
in a multithreaded environment.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
Add fake MP_REACH_NLRI attribute with BGP next hop when encoding MRT
table dumps for IPv6 routes. That is necessary to encode next hop as
NEXT_HOP attribute is not used for MP-BGP.
Thanks to Santiago Aggio for the bugreport.
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
Merge multiple BFD option blocks in BGP configs instead of using the last
one. That is necessary for proper handling of templates when BFD options
are used both in a BGP template and in a BGP protocol derived from that
template.
