The prune loop may may rebuild the prefix trie and therefore invalidate
walk state for asynchronous walks (used in 'show route in' cmd). Fix it
by adding locking that keeps the old trie in memory until current walks
are done.
In future this could be improved by rebuilding trie walk states (by
lookup for last found prefix) after the prefix trie rebuild.
When rtable is pruned and network fib nodes are removed, we also need to
prune prefix trie. Unfortunately, rebuilding prefix trie takes long time
(got about 400 ms for 1M networks), so must not be atomic, we have to
rebuild a new trie while current one is still active. That may require
some considerable amount of temporary memory, so we do that only if
we expect significant trie size reduction.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
When output of 'show route' command was generated, the net_format() was
called for each network prematurely, even if the result was not needed.
Fix the code to call net_format() only when needed. This makes queries
that process many networks but show only few (e.g. 'show route where ..',
or 'show route count') much faster (like 5x - 10x faster).
Attach a prefix trie to IP/VPN/ROA tables. Use it for net_route() and
net_roa_check(). This leads to 3-5x speedups for IPv4 and 5-10x
speedup for IPv6 of these calls.
TODO:
- Rebuild the trie during rt_prune_table()
- Better way to avoid trie_add_prefix() in net_get() for existing tables
- Make it configurable (?)
Add operators .min and .max to find minumum or maximum element in sets
of types: clist, eclist, lclist. Example usage:
bgp_community.min
bgp_ext_community.max
filter(bgp_large_community, [(as1, as2, *)]).min
Signed-off-by: Alexander Zubkov <green@qrator.net>
Compare all IA_* flags that are set by sysdep iface code.
The old code ignores IA_SECONDARY flag when comparing whether iface
address updates from kernel changed anything. This is usually not an
issue as kernel removes all secondary addresses due to removal of the
primary one, but it breaks when sysctl 'promote_secondaries' is enabled
and kernel promotes secondary addresses to primary ones.
Thanks to 'Alexander' for the bugreport.
This feature is intended mostly for checking that BIRD's allocation
strategies don't consume much memory space. There are some cases where
withdrawing routes in a specific order lead to memory fragmentation and
this output should give the user at least a notion of how much memory is
actually used for data storage and how much memory is "just allocated"
or used for overhead.
Also raising the "system allocator overhead estimation" from 8 to 16
bytes; it is probably even more. I've found 16 as a local minimum in
best scenarios among reachable machines. I couldn't find any reasonable
method to estimate this value when BIRD starts up.
This commit also fixes the inaccurate computation of memory overhead for
slabs where the "system allocater overhead estimation" was improperly
added to the size of mmap-ed memory.
Pipes copy the original rte with old values, so they require rte to be
exported with stored tmpattrs. Other protocols access stored attributes
using eattr list, so they require rte to be exported with expanded
tmpattrs. This is temporary hack, we plan to remove whoe tmpattr mechanism.
Thanks to Paul Donohue for the bugreport.
In most cases of export there is no need to store back temporary
attributes to rte, as receivers (protocols) access eattr list anyway.
But pipe copies the original rte with old values, so we should store
tmpattrs also during export.
Thanks to Paul Donohue for the bugreport.
Add support for specifying a password in hexadecimal format, The result
is the same whether a password is specified as a quoted string or a
hex-encoded byte string, this just makes it more convenient to input
high-entropy byte strings as MAC keys.
The Babel MAC authentication RFC recommends implementing Blake2s as one of
the supported algorithms. In order to achieve do this, add the blake2b and
blake2s hash functions for MAC authentication. The hashing function
implementations are the reference implementations from blake2.net.
The Blake2 algorithms allow specifying an arbitrary output size, and the
Babel MAC spec says to implement Blake2s with 128-bit output. To satisfy
this, we add two different variants of each of the algorithms, one using
the default size (256 bits for Blake2s, 512 bits for Blake2b), and one
using half the default output size.
Update to BIRD coding style done by committer.
In general, events are code handling some some condition, which is
scheduled when such condition happened and executed independently from
I/O loop. Work-events are a subgroup of events that are scheduled
repeatedly until some (often significant) work is done (e.g. feeding
routes to protocol). All scheduled events are executed during each
I/O loop iteration.
Separate work-events from regular events to a separate queue and
rate limit their execution to a fixed number per I/O loop iteration.
That should prevent excess latency when many work-events are
scheduled at one time (e.g. simultaneous reload of many BGP sessions).
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
If there are roa_check() calls in channel filters, then the channel
subscribes to ROA table notifications, which are sent when ROA tables
are updated (subject to settle time) and trigger channel reload or
refeed.
The patch add support for per-channel debug flags, currently just
'states', 'routes', and 'filters'. Flag 'states' is used for channel
state changes, remaining two for routes passed through the channel.
The per-protocol debug flags 'routes'/'filters' still enable reporting
of routes for all channels, to keep existing behavior.
The patch causes minor changes in some log messages.
When config structures are copied due to template application,
we need to reset list node structure before calling add_tail().
Thanks to Mikael Magnusson for patches.
Logging as a result of triggered receive limit in import table code
accesset rte->net, which was not filed yet.
Thanks to Pier Carlo Chiodi for the bugreport.
Merge multiple BFD option blocks in BGP configs instead of using the last
one. That is necessary for proper handling of templates when BFD options
are used both in a BGP template and in a BGP protocol derived from that
template.
BFD session options are configured per interface in BFD protocol. This
patch allows to specify them also per-request in protocols requesting
sessions (currently limited to BGP).
Put new non-best routes to the end of list instead of the second
position. Put updated routes to their old position. Position is changed
just by best route selection.
Most commands like 'show ospf neighbors' fail when protocol is not
specified and there are multiple instances of given protocol type.
This is annoying in BIRD 2, as many protocols have IPv4 and IPv6
instances. The patch changes that by showing output from all protocol
instances of appropriate type.
Note that the patch also removes terminating cli_msg() call from these
commands and moves it to the common iterating code.
There is nothing in RFCs specifying that id 0 is not allowed. Some
implementations does not support it, while some other use key id 0 by
default. We allow it but start with key id 1 by default.
Thanks to Kenth Eriksson for the bugreport.
Implement regex-like '+' operator in BGP path masks to match previous
path mask item multiple times. This is useful as ASNs may appear
multiple times in paths due to path prepending for traffic engineering
purposes.
Resolve neighbors using longest prefix match. Although interface ranges
should not generally collide, it may happen for unnumbered links.
Thanks to Kenth Eriksson for the bugreport.
