The effective keepalive time now scales relative to the negotiated
hold time, to maintain proportion between the keepalive time and the
hold time. This avoids issues when both keepalive and hold times
were configured, the hold time was negotiated to a smaller value,
but the keepalive time stayed the same.
Add new options 'min hold time' and 'min keepalive time', which reject
session attempts with too small hold time.
Improve validation of config options an their documentation.
Thanks to Alexander Zubkov and Sergei Goriunov for suggestions.
Add BGP channel option 'next hop prefer global' that modifies BGP
recursive next hop resolution to use global next hop IPv6 address instead
of link-local next hop IPv6 address for immediate next hop of received
routes.
In principle, the channel list is a list of parent struct proto and can
contain general structures of type struct channel, That is useful e.g.
for adding MPLS channels to BGP.
Implement BGP roles as described in RFC 9234. It is a mechanism for
route leak prevention and automatic route filtering based on common BGP
topology relationships. It defines role capability (controlled by 'local
role' option) and OTC route attribute, which is used for automatic route
filtering and leak detection.
Minor changes done by commiter.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
Routes from downed protocols stay in rtable (until next rtable prune
cycle ends) and may be even exported to another protocol. In BGP case,
source BGP protocol is examined, although dynamic parts (including
neighbor entries) are already freed. That may lead to crash under some
race conditions. Ensure that freed neighbor entry is not accessed to
avoid this issue.
BGP statistics code was preliminary and i wanted to replace it by
separate 'show X stats' command. The patch hides the preliminary
output in 'show protocols all' so it is not part of the released
version.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
BFD session options are configured per interface in BFD protocol. This
patch allows to specify them also per-request in protocols requesting
sessions (currently limited to BGP).
When dynamic BGP with remote range is configured, MD5SIG needs to use
newer socket option (TCP_MD5SIG_EXT) to specify remote addres range for
listening socket.
Thanks to Adam Kułagowski for the suggestion.
This is optional check described in RFC 4271. Although this can be also
done by filters, it is widely implemented option in BGP implementations.
Thanks to Eugene Bogomazov for the original patch.
Change of some options requires route refresh, but when import table is
active, channel reload is done from it instead of doing full route
refresh. So in this case we request it internally.
The patch implements optional internal export table to a channel and
hooks it to BGP so it can be used as Adj-RIB-Out. When enabled, all
exported (post-filtered) routes are stored there. An export table can be
examined using e.g. 'show route export table bgp1.ipv4'.
Several BGP channel options (including 'next hop self') could be
reconfigured without session reset, with just route refeed/refresh.
The patch improves reconfiguration code to do it that way.
When 'graceful down' command is entered, protocols are shut down
with regard to graceful restart. Namely Kernel protocol does
not remove routes and BGP protocol does not send notification,
just closes the connection.
Useful for implementation of agents implementing the SNMP-BGP MIB, which
requires the local AS of a session to be specified.
Thanks to Jan-Philipp Litza for the patch.
Support for dynamically spawning BGP protocols for incoming connections.
Use 'neighbor range' to specify range of valid neighbor addresses, then
incoming connections from these addresses spawn new BGP instances.
When BGP connection is opened, it may happen that rx hook (with remote
OPEN) is called before tx hook (for local OPEN). Therefore, we need to do
internal changes (like setting local_caps) synchronously with OPENSENT
transition and we need to ensure that OPEN is sent before KEEPALIVE.
Allow to specify just 'internal' or 'external' for remote neighbor
instead of specific ASN. In the second case that means BGP peers with
any non-local ASNs are accepted.
Since v2 we have multiple listening BGP sockets, and each BGP protocol
has associated one of them. Use listening socket that accepted the
incoming connection as a key in the dispatch process so only BGP
protocols assocaited with that listening socket can be selected.
This is necesary for proper dispatch when VRFs are used.
Extend 'next hop keep' and 'next hop self' options to have boolean values
(enabled / disabled) and also values 'ibgp'/ 'ebgp' to restrict it to
routes received from IBGP / EBGP. This allows to have it enabled by
default in some cases, matches features of other implementations, and
allows to handle some strange cases like EBGP border router with 'next
hop self' also doing IBGP route reflecting.
Change default of 'next hop keep' to enabled for route servers, and
'ibgp' for route reflectors.
Update documentation for these options.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
