When filtered routes (enabled by 'import keep filtered' option) are
updated, they trigger announcements by rte_announce(). For regular
channels (e.g. type RA_OPTIMAL or RA_ANY) such announcement is just
ignored, but in case of RA_ACCEPTED (BGP peer with 'secondary' option)
it just reannounces the old (and still valid) best route.
The patch ensures that such no-change is ignored even for these channels.
Add BGP channel option 'next hop prefer global' that modifies BGP
recursive next hop resolution to use global next hop IPv6 address instead
of link-local next hop IPv6 address for immediate next hop of received
routes.
It is useful to distinguish whehter channel config returned from
channel_config_get() was allocated new, or existing from template.
Caller may want to initialize new ones.
In principle, the channel list is a list of parent struct proto and can
contain general structures of type struct channel, That is useful e.g.
for adding MPLS channels to BGP.
In some specific configurations, it was possible to send BIRD into an
infinite loop of recursive next hop resolution. This was caused by route
priority inversion.
To prevent priority inversions affecting other next hops, we simply
refuse to resolve any next hop if the best route for the matching prefix
is recursive or any other route with the same preference is recursive.
Next hop resolution doesn't change route priority, therefore it is
perfectly OK to resolve BGP next hops e.g. by an OSPF route, yet if the
same (or covering) prefix is also announced by iBGP, by retraction of
the OSPF route we would get a possible priority inversion.
For loops allow to iterate over elements in compound data like BGP paths
or community lists. The syntax is:
for [ <type> ] <variable> in <expr> do <command-body>
When f_line is done, we have to pop the stack frame. The old code just
removed nominal number of args/vars. Change it to use stored ventry value
modified by number of returned values. This allows to allocate variables
on a stack frame during execution of f_lines instead of just at start.
But we need to know the number of returned values for a f_line. It is 1
for term, 0 for cmd. Store that to f_line during linearization.
Passing protocol to preexport was in fact a historical relic from the
old times when channels weren't a thing. Refactoring that to match
current extensibility needs.
Use timer (configurable as 'gc period') to schedule routing table
GC/pruning to ensure that prune is done on time but not too often.
Randomize GC timers to avoid concentration of GC events from different
tables in one loop cycle.
Fix a bug that caused minimum inter-GC interval be 5 us instead of 5 s.
Make default 'gc period' adaptive based on number of routing tables,
from 10 s for small setups to 600 s for large ones.
In marge multi-table RS setup, the patch improved time of flushing
a downed peer from 20-30 min to <2 min and removed 40s latencies.
The prefix hash table in BGP used the same hash function as the rtable.
When a batch of routes are exported during feed/flush to the BGP, they
all have similar hash values, so they are all crowded in a few slots in
the BGP prefix table (which is much smaller - around the size of the
batch - and uses higher bits from hash values), making it much slower due
to excessive collisions. Use a different hash function to avoid this.
Also, increase the batch size to fill 4k BGP packets and increase minimum
BGP bucket and prefix hash sizes to avoid back and forth resizing during
flushes.
This leads to order of magnitude faster flushes (on my test data).
The interface pointer was improperly converted to u32 and back. Fixing
this by explicitly allocating an adata structure for it. It's not so
memory efficient, we'll optimize this later.
The prune loop may may rebuild the prefix trie and therefore invalidate
walk state for asynchronous walks (used in 'show route in' cmd). Fix it
by adding locking that keeps the old trie in memory until current walks
are done.
In future this could be improved by rebuilding trie walk states (by
lookup for last found prefix) after the prefix trie rebuild.
When rtable is pruned and network fib nodes are removed, we also need to
prune prefix trie. Unfortunately, rebuilding prefix trie takes long time
(got about 400 ms for 1M networks), so must not be atomic, we have to
rebuild a new trie while current one is still active. That may require
some considerable amount of temporary memory, so we do that only if
we expect significant trie size reduction.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
When output of 'show route' command was generated, the net_format() was
called for each network prematurely, even if the result was not needed.
Fix the code to call net_format() only when needed. This makes queries
that process many networks but show only few (e.g. 'show route where ..',
or 'show route count') much faster (like 5x - 10x faster).
Attach a prefix trie to IP/VPN/ROA tables. Use it for net_route() and
net_roa_check(). This leads to 3-5x speedups for IPv4 and 5-10x
speedup for IPv6 of these calls.
TODO:
- Rebuild the trie during rt_prune_table()
- Better way to avoid trie_add_prefix() in net_get() for existing tables
- Make it configurable (?)
Add operators .min and .max to find minumum or maximum element in sets
of types: clist, eclist, lclist. Example usage:
bgp_community.min
bgp_ext_community.max
filter(bgp_large_community, [(as1, as2, *)]).min
Signed-off-by: Alexander Zubkov <green@qrator.net>
Compare all IA_* flags that are set by sysdep iface code.
The old code ignores IA_SECONDARY flag when comparing whether iface
address updates from kernel changed anything. This is usually not an
issue as kernel removes all secondary addresses due to removal of the
primary one, but it breaks when sysctl 'promote_secondaries' is enabled
and kernel promotes secondary addresses to primary ones.
Thanks to 'Alexander' for the bugreport.
This feature is intended mostly for checking that BIRD's allocation
strategies don't consume much memory space. There are some cases where
withdrawing routes in a specific order lead to memory fragmentation and
this output should give the user at least a notion of how much memory is
actually used for data storage and how much memory is "just allocated"
or used for overhead.
Also raising the "system allocator overhead estimation" from 8 to 16
bytes; it is probably even more. I've found 16 as a local minimum in
best scenarios among reachable machines. I couldn't find any reasonable
method to estimate this value when BIRD starts up.
This commit also fixes the inaccurate computation of memory overhead for
slabs where the "system allocater overhead estimation" was improperly
added to the size of mmap-ed memory.
