New LSA checksumming code separates generic Fletcher-16 and OSPF-specific
code and avoids back and forth endianity conversions, making it much more
readable and also several times faster.
Prior to this patch, BIRD validates the OSPF LSA checksum by calculating
a new checksum and comparing it with the checksum in the header. Due to
the specifics of the Fletcher checksum used in OSPF, this is not
necessarily correct as the checkbytes in the header may be calculated via
a different means and end up with a different value that is nonetheless
still correct.
The documented means of validating the checksum as specified in RFC 905
B.4 is to calculate c0 and c1 from the unchanged contents of the packet,
which must result in a zero value to be considered valid.
Thanks to Chris Boot for the patch.
Prior to this patch, BIRD validates the OSPF LSA checksum by calculating
a new checksum and comparing it with the checksum in the header. Due to
the specifics of the Fletcher checksum used in OSPF, this is not
necessarily correct as the checkbytes in the header may be calculated via
a different means and end up with a different value that is nonetheless
still correct.
The documented means of validating the checksum as specified in RFC 905
B.4 is to calculate c0 and c1 from the unchanged contents of the packet,
which must result in a zero value to be considered valid.
Thanks to Chris Boot for the patch.
Fixes cases where the same network or external route are propagated by
several OSPF routes and some other corner cases in next hop construction
and ECMP. Allows to specify whether external routes should be merged.
Thanks to Peter Christensen for the original patch.
I/O:
- BSD: specify src addr on IP sockets by IP_HDRINCL
- BSD: specify src addr on UDP sockets by IP_SENDSRCADDR
- Linux: specify src addr on IP/UDP sockets by IP_PKTINFO
- IPv6: specify src addr on IP/UDP sockets by IPV6_PKTINFO
- Alternative SKF_BIND flag for binding to IP address
- Allows IP/UDP sockets without tx_hook, on these
sockets a packet is discarded when TX queue is full
- Use consistently SOL_ for socket layer values.
OSPF:
- Packet src addr is always explicitly set
- Support for secondary addresses in BSD
- Dynamic RX/TX buffers
- Fixes some minor buffer overruns
- Interface option 'tx length'
- Names for vlink pseudoifaces (vlinkX)
- Vlinks use separate socket for TX
- Vlinks do not use fixed associated iface
- Fixes TTL for direct unicast packets
- Fixes DONTROUTE for OSPF sockets
- Use ifa->ifname instead of ifa->iface->name
Interfaces for OSPF and RIP could be configured to use (and request)
TTL 255 for traffic to direct neighbors.
Thanks to Simon Dickhoven for the original patch for RIPng.
Implements support for IPv6 traffic class, sets higher priority for OSPF
and RIP outgoing packets by default and allows to configure ToS/DS/TClass
IP header field and the local priority of outgoing packets.
BIRD used zero netmask in hello packets on all PtP links, not just on
unnumbered ones. This patch fixes it and adds option 'ptp netmask'
for overriding the default behavior.
Thanks to Alexander V. Chernikov for the original patch.
Configured NBMA neighbors in OSPFv3 should be link-local addresses, old
behavior was to silently ignore global ones. The patch allows BIRD to
accept global ones, but adds a warning and a documentation notice.
Thanks to Wilco Baan Hofman for the bugreport.
Router ID could be automatically determined based of subset of
ifaces/addresses specified by 'router id from' option. The patch also
does some minor changes related to router ID reconfiguration.
Thanks to Alexander V. Chernikov for most of the work.
Although it is a slight deviation from the standard, it has no ill
consequences for OSPFv2 and the change fixes a compatibility issue
with some broken implementations.
