The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
The patch implements BGP Administrative Shutdown Communication (RFC 8203)
allowing BGP operators to pass messages related to BGP session
administrative shutdown/restart. It handles both transmit and receive of
shutdown messages. Messages are logged and may be displayed by show
protocol all command.
Thanks to Job Snijders for the basic patch.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
Covers IPv4/VPNv4 routes with IPv6 next hop (RFC 5549), IPv6 routes with
IPv4 next hop (RFC 4798) and VPNv6 routes with IPv4 next hop (RFC 4659).
Unfortunately it also makes next hop hooks more messy.
Each BGP channel now could have two IGP tables, one for IPv4 next hops,
the other for IPv6 next hops.
Basic support for SAFI 4 and 128 (MPLS labeled IP and VPN) for IPv4 and
IPv6. Should work for route reflector, but does not properly handle
originating routes with next hop self.
Based on patches from Jan Matejka.
Prefix and bucket tables are initialized when entering established state
but not explicitly freed when leaving it (that is handled by protocol
restart). With graceful restart, BGP may enter and leave established
state multiple times without hard protocol restart causing memory leak.
Add code for manipulation with TCP-MD5 keys in the IPsec SA/SP database
at FreeBSD systems. Now, BGP MD5 authentication (RFC 2385) keys are
handled automatically on both Linux and FreeBSD.
Based on patches from Pavel Tvrdik.
In BIRD, RX has lower priority than TX with the exception of RX from
control socket. The patch replaces heuristic based on socket type with
explicit mark and uses it for both control socket and BGP session waiting
to be established.
This should avoid an issue when during heavy load, outgoing connection
could connect (TX event), send open, but then failed to receive OPEN /
establish in time, not sending notifications between and therefore
got hold timer expired error from the neighbor immediately after it
finally established the connection.
When a BGP session was established by an outgoing connection with
Graceful Restart behavior negotiated, a pending incoming connection in
OpenSent state, and another incoming connection was received, then the
outgoing connection (and whole BGP session) was closed, but the old
incoming connection was just overwritten by the new one. That later
caused a crash when the hold timer from the old connection fired.
The patch adds support for channels, structures connecting protocols and
tables and handling most interactions between them. The documentation is
missing yet.
Permit specifying neighbor address, AS number and port independently.
Add 'interface' parameter for specifying interface for link-local
sessions independently.
Thanks to Alexander V. Chernikov for the original patch.
This is more consistent with common usage and also with the behavior of
other implementations (Cisco, Juniper).
Also changes the default for gw mode to be based solely on
direct/multihop.
Neighbor events related to received route next hops got mixed up with
sticky neighbor node for an IP of the BGP peer. If a neighbor for a next
hop disappears, BGP session is shut down.
Router ID could be automatically determined based of subset of
ifaces/addresses specified by 'router id from' option. The patch also
does some minor changes related to router ID reconfiguration.
Thanks to Alexander V. Chernikov for most of the work.
When 'import keep rejected' protocol option is activated, routes
rejected by the import filter are kept in the routing table, but they
are hidden and not propagated to other protocols. It is possible to
examine them using 'show route rejected'.
Allows to send and receive multiple routes for one network by one BGP
session. Also contains necessary core changes to support this (routing
tables accepting several routes for one network from one protocol).
It needs some more cleanup before merging to the master branch.
The nest-protocol interaction is changed to better handle multitable
protocols. Multitable protocols now declare that by 'multitable' field,
which tells nest that a protocol handles things related to proto-rtable
interaction (table locking, announce hook adding, reconfiguration of
filters) itself.
Filters and stats are moved to announce hooks, a protocol could have
different filters and stats to different tables.
The patch is based on one from Alexander V. Chernikov, thanks.
Hostcache is a structure for monitoring changes in a routing table that
is used for routes with dynamic/recursive next hops. This is needed for
proper iBGP next hop handling.
There is no reak callback scheduler and previous behavior causes
bad things during hard congestion (like BGP hold timeouts).
Smart callback scheduler is still missing, but main loop was
changed such that it first processes all tx callbacks (which
are fast enough) (but max 4* per socket) + rx callbacks for CLI,
and in the second phase it processes one rx callback per
socket up to four sockets (as rx callback can be slow when
there are too many protocols, because route redistribution
is done synchronously inside rx callback). If there is event
callback ready, second phase is skipped in 90% of iterations
(to speed up CLI during congestion).
