Support for dynamically spawning BGP protocols for incoming connections.
Use 'neighbor range' to specify range of valid neighbor addresses, then
incoming connections from these addresses spawn new BGP instances.
This protocol is highly experimental and nobody should use it in
production. Anyway it may help you getting some insight into what eats
so much time in filter processing.
The patch d506263d... blocked adding channel during reconfiguration,
that broke protocols which use the same functiona also during init.
This patch fixes that.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
When a new channel is found during reconfiguration, do force restart
of the protocol, like with any other un-reconfigurable change.
The old behavior was that the new channel was added but remained in down
state, even if the protocol was up, so a manual protocol restart was
often necessary.
In the future this should be improved such that a reconfigurable
channel addition (e.g. direct) is accepted and channel is started,
while an un-reconfigurable addition forces protocol restart.
The new MRT protocol is responsible for periodic RIB table dumps in the
MRT format (RFC 6396). Also the existing code for BGP4MP MRT dumps is
refactored and splitted between BGP to MRT protocols, will be more
integrated into MRT in the future.
Example:
protocol mrt {
table "*";
filename "%N_%F_%T.mrt";
period 60;
}
It is partially based on the old MRT code from Pavel Tvrdik.
If export filter is changed during reconfiguration and a route disappears
between reconfiguration and refeed (e.g., if the route is a static route
also removed during the reconfiguration), the route is not withdrawn.
The patch fixes that by adding tx reconfiguration timestamp.
The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
The patch implements BGP Administrative Shutdown Communication (RFC 8203)
allowing BGP operators to pass messages related to BGP session
administrative shutdown/restart. It handles both transmit and receive of
shutdown messages. Messages are logged and may be displayed by show
protocol all command.
Thanks to Job Snijders for the basic patch.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
Some code cleanup, multiple bugfixes, allows to specify also channel
for 'show route export'. Interesting how such apparenty simple thing
like show route cmd has plenty of ugly corner cases.
This patch implements the IPv6 subset of the Babel routing protocol.
Based on the patch from Toke Hoiland-Jorgensen, with some heavy
modifications and bugfixes.
Thanks to Toke Hoiland-Jorgensen for the original patch.
Counter exp_routes is increased during initial route feed after GR
recovery, so it has to start with zero, otherwise BIRD will end with
double value in exp_routes.
The patch adds support for channels, structures connecting protocols and
tables and handling most interactions between them. The documentation is
missing yet.
Symbol lookup by cf_find_symbol() not only did the lookup but also added
new void symbols allocated from cfg_mem linpool, which gets broken when
lookups are done outside of config parsing, which may lead to crashes
during reconfiguration.
The patch separates lookup-only cf_find_symbol() and config-modifying
cf_get_symbol(), while the later is called only during parsing. Also
new_config and cfg_mem global variables are NULLed outside of parsing.
