On Linux, setting the ToS will also set the priority and the range of
accepted values is quite limited (masked by 0x1e). Therefore, 0xc0 is
translated to a priority of 0, not something we want, overriding the
"7" priority which was set previously explicitely. To avoid that, just
move setting priority later in the code.
Thanks to Vincent Bernat for the patch.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
==00:00:00:02.831 2468== Syscall param socketcall.setsockopt(optval) points to uninitialised byte(s)
==00:00:00:02.831 2468== at 0x513BDEA: setsockopt (in /usr/lib/libc-2.23.so)
==00:00:00:02.831 2468== by 0x45C7AF: sk_setup (io.c:1216)
==00:00:00:02.831 2468== by 0x45CDFF: sk_open (io.c:1417)
==00:00:00:02.831 2468== by 0x44B562: rip_open_socket (packets.c:740)
==00:00:00:02.831 2468== by 0x4481A7: rip_iface_locked (rip.c:616)
==00:00:00:02.831 2468== by 0x4133E4: olock_run_event (locks.c:177)
==00:00:00:02.831 2468== by 0x45A6DE: ev_run (event.c:85)
==00:00:00:02.831 2468== by 0x45A7AD: ev_run_list (event.c:142)
==00:00:00:02.831 2468== by 0x45E0FC: io_loop (io.c:2066)
==00:00:00:02.831 2468== by 0x463B56: main (main.c:845)
==00:00:00:02.831 2468== Address 0xffefffd24 is on thread 1's stack
==00:00:00:02.831 2468== in frame #1, created by sk_setup (io.c:1188)
==00:00:00:02.831 2468== Uninitialised value was created by a stack allocation
==00:00:00:02.831 2468== at 0x45C6BB: sk_setup (io.c:1188)
Add code for manipulation with TCP-MD5 keys in the IPsec SA/SP database
at FreeBSD systems. Now, BGP MD5 authentication (RFC 2385) keys are
handled automatically on both Linux and FreeBSD.
Based on patches from Pavel Tvrdik.
In BIRD, RX has lower priority than TX with the exception of RX from
control socket. The patch replaces heuristic based on socket type with
explicit mark and uses it for both control socket and BGP session waiting
to be established.
This should avoid an issue when during heavy load, outgoing connection
could connect (TX event), send open, but then failed to receive OPEN /
establish in time, not sending notifications between and therefore
got hold timer expired error from the neighbor immediately after it
finally established the connection.
If the number of sockets is too much for select(), we should at least
handle it with proper error messages and reject new sockets instead of
breaking the event loop.
Thanks to Alexander V. Chernikov for the patch.
Although RFC 3542 allows both cases, Theo de Raadt thinks
he knows better, and msg_controllen without last padding
fails on OpenBSD.
Thanks to Job Snijders for the bugreport.
I/O:
- BSD: specify src addr on IP sockets by IP_HDRINCL
- BSD: specify src addr on UDP sockets by IP_SENDSRCADDR
- Linux: specify src addr on IP/UDP sockets by IP_PKTINFO
- IPv6: specify src addr on IP/UDP sockets by IPV6_PKTINFO
- Alternative SKF_BIND flag for binding to IP address
- Allows IP/UDP sockets without tx_hook, on these
sockets a packet is discarded when TX queue is full
- Use consistently SOL_ for socket layer values.
OSPF:
- Packet src addr is always explicitly set
- Support for secondary addresses in BSD
- Dynamic RX/TX buffers
- Fixes some minor buffer overruns
- Interface option 'tx length'
- Names for vlink pseudoifaces (vlinkX)
- Vlinks use separate socket for TX
- Vlinks do not use fixed associated iface
- Fixes TTL for direct unicast packets
- Fixes DONTROUTE for OSPF sockets
- Use ifa->ifname instead of ifa->iface->name
RIP sockets for multiple ifaces collided, because we cannot bind to
a specific iface on BSD. Workarounded by SO_REUSEPORT.
Thanks to Eugene M. Zheganin for the bugreport.
Interfaces for OSPF and RIP could be configured to use (and request)
TTL 255 for traffic to direct neighbors.
Thanks to Simon Dickhoven for the original patch for RIPng.
Implements support for IPv6 traffic class, sets higher priority for OSPF
and RIP outgoing packets by default and allows to configure ToS/DS/TClass
IP header field and the local priority of outgoing packets.
Several new configure command variants:
configure undo - undo last reconfiguration
configure timeout - configure with scheduled undo if not confirmed in timeout
configure confirm - confirm last configuration
configure check - just parse and validate config file
