Added an option for export filter to allow for prefiltering based on the
prefix. Routes outside the given prefix are completely ignored. Config
is simple:
export in <net> <filter>;
Use timer (configurable as 'gc period') to schedule routing table
GC/pruning to ensure that prune is done on time but not too often.
Randomize GC timers to avoid concentration of GC events from different
tables in one loop cycle.
Fix a bug that caused minimum inter-GC interval be 5 us instead of 5 s.
Make default 'gc period' adaptive based on number of routing tables,
from 10 s for small setups to 600 s for large ones.
In marge multi-table RS setup, the patch improved time of flushing
a downed peer from 20-30 min to <2 min and removed 40s latencies.
The route scope attribute was used for simple user route marking. As
there is a better tool for this (custom attributes), the old and limited
way can be dropped.
Add BFD protocol option 'strict bind' to use separate listening socket
for each BFD interface bound to its address instead of using shared
listening sockets.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
Add option 'netlink rx buffer' to specify netlink socket receive buffer
size. Uses SO_RCVBUFFORCE, so it can override rmem_max limit.
Thanks to Trisha Biswas and Michal for the original patches.
We can also quite simply allocate bigger blocks. Anyway, we need these
blocks to be aligned to their size which needs one mmap() two times
bigger and then two munmap()s returning the unaligned parts.
The user can specify -B <N> on startup when <N> is the exponent of 2,
setting the block size to 2^N. On most systems, N is 12, anyway if you
know that your configuration is going to eat gigabytes of RAM, you are
almost forced to raise your block size as you may easily get into memory
fragmentation issues or you have to raise your maximum mapping count,
e.g. "sysctl vm.max_map_count=(number)".
Some cleanups and bugfixes to the previous patch, including:
- Fix rate limiting in index mismatch check
- Fix missing BABEL_AUTH_INDEX_LEN in auth_tx_overhead computation
- Fix missing auth_tx_overhead recalculation during reconfiguration
- Fix pseudoheader construction in babel_auth_sign() (sport vs fport)
- Fix typecasts for ptrdiffs in log messages
- Make auth log messages similar to corresponding RIP/OSPF ones
- Change auth log messages for events that happen during regular
operation to debug messages
- Switch meaning of babel_auth_check*() functions for consistency
with corresponding RIP/OSPF ones
- Remove requirement for min/max key length, only those required by
given MAC code are enforced
This implements support for MAC authentication in the Babel protocol, as
specified by RFC 8967. The implementation seeks to follow the RFC as close
as possible, with the only deliberate deviation being the addition of
support for all the HMAC algorithms already supported by Bird, as well as
the Blake2b variant of the Blake algorithm.
For description of applicability, assumptions and security properties,
see RFC 8967 sections 1.1 and 1.2.
Add support for specifying a password in hexadecimal format, The result
is the same whether a password is specified as a quoted string or a
hex-encoded byte string, this just makes it more convenient to input
high-entropy byte strings as MAC keys.
The Babel MAC authentication RFC recommends implementing Blake2s as one of
the supported algorithms. In order to achieve do this, add the blake2b and
blake2s hash functions for MAC authentication. The hashing function
implementations are the reference implementations from blake2.net.
The Blake2 algorithms allow specifying an arbitrary output size, and the
Babel MAC spec says to implement Blake2s with 128-bit output. To satisfy
this, we add two different variants of each of the algorithms, one using
the default size (256 bits for Blake2s, 512 bits for Blake2b), and one
using half the default output size.
Update to BIRD coding style done by committer.
For numeric operators, comma is used for disjunction in expressions like
"10, 20, 30..40". But for bitmask operators, comma is used for
conjunction in a way that does not really make much sense. Use always
explicit logical operators (&& and ||) to connect bitmask operators.
Thanks to Matt Corallo for the bugreport.
Add support to set or read outgoing MPLS labels using filters. Currently
this supports the addition of one label per route for the first next hop.
Minor changes by committer.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
Add 'weight' route attribute that allows to get and set ECMP weight of
nexthops. Similar to 'gw' attribute, it is limited to the first nexthop,
but it is useful for handling BGP multipath, where an ECMP route is
merged from multiple regular routes.
Add support for proper handling of multiple routes with the same network
to the static protocol. Routes are distinguished by internal index, which
is assigned automatically (sequentially for routes within each network).
Having different route preference or igp_metric attribute is optional.
Add 'ignore max length' option to RPKI protocol, which ignores received
max length in ROA records and instead uses max value (32 or 128). This
may be useful for implementing loose RPKI check for blackholes.
This issue has a long history. In 2012, we changed data field for
unnumbered PtP links from iface id (specified by RFC) to IP address based
on reports of bugs in Quagga that required it, and we used out-of-band
information to distinquish unnumberred PtPs with the same local IP
address.
Then with OSPF graceful restart implementation, we found that we can no
longer use out-of-band information, and we need to use only LSAdb info
for routing table calculation, but i forgot to finish handling of this
case, so multiple unnumbered PtPs with the same local IP addresses were
broken.
Considering that even recent Mikrotik RouterOS has broken next hop
calculation that depends on IP address in PtP link data field, we
cannot just switch back to the iface id for unnumbered PtP links.
The patch makes two changes: First, it goes back to use out-of-band
(position) info for distinguishing local interfaces in SPF when graceful
restart is not enabled, while still uses LSAdb-only approach for SPF
calculation when graceful restart is enabled.
Second, it adds OSPF interface option 'ptp address', which controls
whether IP address or iface id is used in data field. It is enabled
by default except for unnumbered PtP links with enabled graceful
restart.
Thanks to Kenth Eriksson for the bugreport and Joakim Tjernlund for
suggestions.
