Protocol can have specified VRF, in such case it is restricted to a set
of ifaces associated with the VRF, otherwise it can use all interfaces.
The patch allows to specify VRF as 'default', in which case it is
restricted to a set of iface not associated with any VRF.
This is a major change of how the filters are interpreted. If everything
works how it should, it should not affect you unless you are hacking the
filters themselves.
Anyway, this change should make a huge improvement in the filter performance
as previous benchmarks showed that our major problem lies in the
recursion itself.
There are also some changes in nest and protocols, related mostly to
spreading const declarations throughout the whole BIRD and also to
refactored dynamic attribute definitions. The need of these came up
during the whole work and it is too difficult to split out these
not-so-related changes.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
For local route marking purposes, local custom route attributes may be
defined. These attributes are seamlessly stripped after export filter to
every real protocol like Kernel, BGP or OSPF, they however pass through
pipes. We currently allow at most 256 custom attributes.
This should be much faster than currently used bgp communities
for marking routes.
This patch adds support for source-specific IPv6 routes to BIRD core.
This is based on Dean Luga's original patch, with the review comments
addressed. SADR support is added to network address parsing in confbase.Y
and to the kernel protocol on Linux.
Currently there is no way to mix source-specific and non-source-specific
routes (i.e., SADR tables cannot be connected to non-SADR tables).
Thanks to Toke Hoiland-Jorgensen for the original patch.
Minor changes by Ondrej Santiago Zajicek.
The patch implements BGP Administrative Shutdown Communication (RFC 8203)
allowing BGP operators to pass messages related to BGP session
administrative shutdown/restart. It handles both transmit and receive of
shutdown messages. Messages are logged and may be displayed by show
protocol all command.
Thanks to Job Snijders for the basic patch.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
Some code cleanup, multiple bugfixes, allows to specify also channel
for 'show route export'. Interesting how such apparenty simple thing
like show route cmd has plenty of ugly corner cases.
Dropped struct mpnh and mpnh_*()
Now struct nexthop exists, nexthop_*(), and also included struct nexthop
into struct rta.
Also converted RTD_DEVICE and RTD_ROUTER to RTD_UNICAST. If it is needed
to distinguish between these two cases, RTD_DEVICE is equivalent to
IPA_ZERO(a->nh.gw), RTD_ROUTER is then IPA_NONZERO(a->nh.gw).
From now on, we also explicitely want C99 compatible compiler. We assume
that this 20-year norm should be known almost everywhere.
This updates the documentation to correctly mention Babel when protocols
are listed, and adds examples and route attribute documentation to the
Babel section of the docs.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
The patch adds support for channels, structures connecting protocols and
tables and handling most interactions between them. The documentation is
missing yet.
Explicit setting of AF_INET(6|) in IP socket creation. BFD set to listen
on v6, without setting the V6ONLY flag to catch both v4 and v6 traffic.
Squashing and minor changes by Ondrej Santiago Zajicek
New data types net_addr and variants (in lib/net.h) describing
network addresses (prefix/pxlen). Modifications of FIB structures
to handle these data types and changing everything to use these
data types instead of prefix/pxlen pairs where possible.
The commit is WiP, some protocols are not yet updated (BGP, Kernel),
and the code contains some temporary scaffolding.
Comments are welcome.
Implemented eval command can be used to evaluate expressions.
The patch also documents echo command and allows to use log classes
instead of integer as a mask for echo.
Implements support for IPv6 traffic class, sets higher priority for OSPF
and RIP outgoing packets by default and allows to configure ToS/DS/TClass
IP header field and the local priority of outgoing packets.
Router ID could be automatically determined based of subset of
ifaces/addresses specified by 'router id from' option. The patch also
does some minor changes related to router ID reconfiguration.
Thanks to Alexander V. Chernikov for most of the work.
When 'import keep rejected' protocol option is activated, routes
rejected by the import filter are kept in the routing table, but they
are hidden and not propagated to other protocols. It is possible to
examine them using 'show route rejected'.
- ROA tables, which are used as a basic part for RPKI.
- Commands for examining and modifying ROA tables.
- Filter operators based on ROA tables consistent with RFC 6483.
