By this, the requesting channels do the timers in their own loops,
avoiding unnecessary synchronization when the central timer went off.
This is of course less effective for now, yet it allows to easily
implement selective reloads in future.
These routines detect the export congestion (as defined by configurable
thresholds) and propagate the state to readers. There are no readers for
now, they will be added in following commits.
Implement BGP roles as described in RFC 9234. It is a mechanism for
route leak prevention and automatic route filtering based on common BGP
topology relationships. It defines role capability (controlled by 'local
role' option) and OTC route attribute, which is used for automatic route
filtering and leak detection.
Minor changes done by commiter.
For loops allow to iterate over elements in compound data like BGP paths
or community lists. The syntax is:
for [ <type> ] <variable> in <expr> do <command-body>
Allow variable declarations mixed with code, also in nested blocks with
proper scoping, and with variable initializers. E.g:
function fn(int a)
{
int b;
int c = 10;
if a > 20 then
{
b = 30;
int d = c * 2;
print a, b, c, d;
}
string s = "Hello";
}
Added an option for export filter to allow for prefiltering based on the
prefix. Routes outside the given prefix are completely ignored. Config
is simple:
export in <net> <filter>;
Use timer (configurable as 'gc period') to schedule routing table
GC/pruning to ensure that prune is done on time but not too often.
Randomize GC timers to avoid concentration of GC events from different
tables in one loop cycle.
Fix a bug that caused minimum inter-GC interval be 5 us instead of 5 s.
Make default 'gc period' adaptive based on number of routing tables,
from 10 s for small setups to 600 s for large ones.
In marge multi-table RS setup, the patch improved time of flushing
a downed peer from 20-30 min to <2 min and removed 40s latencies.
The route scope attribute was used for simple user route marking. As
there is a better tool for this (custom attributes), the old and limited
way can be dropped.
Add BFD protocol option 'strict bind' to use separate listening socket
for each BFD interface bound to its address instead of using shared
listening sockets.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
Add option 'netlink rx buffer' to specify netlink socket receive buffer
size. Uses SO_RCVBUFFORCE, so it can override rmem_max limit.
Thanks to Trisha Biswas and Michal for the original patches.
We can also quite simply allocate bigger blocks. Anyway, we need these
blocks to be aligned to their size which needs one mmap() two times
bigger and then two munmap()s returning the unaligned parts.
The user can specify -B <N> on startup when <N> is the exponent of 2,
setting the block size to 2^N. On most systems, N is 12, anyway if you
know that your configuration is going to eat gigabytes of RAM, you are
almost forced to raise your block size as you may easily get into memory
fragmentation issues or you have to raise your maximum mapping count,
e.g. "sysctl vm.max_map_count=(number)".
Some cleanups and bugfixes to the previous patch, including:
- Fix rate limiting in index mismatch check
- Fix missing BABEL_AUTH_INDEX_LEN in auth_tx_overhead computation
- Fix missing auth_tx_overhead recalculation during reconfiguration
- Fix pseudoheader construction in babel_auth_sign() (sport vs fport)
- Fix typecasts for ptrdiffs in log messages
- Make auth log messages similar to corresponding RIP/OSPF ones
- Change auth log messages for events that happen during regular
operation to debug messages
- Switch meaning of babel_auth_check*() functions for consistency
with corresponding RIP/OSPF ones
- Remove requirement for min/max key length, only those required by
given MAC code are enforced
This implements support for MAC authentication in the Babel protocol, as
specified by RFC 8967. The implementation seeks to follow the RFC as close
as possible, with the only deliberate deviation being the addition of
support for all the HMAC algorithms already supported by Bird, as well as
the Blake2b variant of the Blake algorithm.
For description of applicability, assumptions and security properties,
see RFC 8967 sections 1.1 and 1.2.
Add support for specifying a password in hexadecimal format, The result
is the same whether a password is specified as a quoted string or a
hex-encoded byte string, this just makes it more convenient to input
high-entropy byte strings as MAC keys.
The Babel MAC authentication RFC recommends implementing Blake2s as one of
the supported algorithms. In order to achieve do this, add the blake2b and
blake2s hash functions for MAC authentication. The hashing function
implementations are the reference implementations from blake2.net.
The Blake2 algorithms allow specifying an arbitrary output size, and the
Babel MAC spec says to implement Blake2s with 128-bit output. To satisfy
this, we add two different variants of each of the algorithms, one using
the default size (256 bits for Blake2s, 512 bits for Blake2b), and one
using half the default output size.
Update to BIRD coding style done by committer.
For numeric operators, comma is used for disjunction in expressions like
"10, 20, 30..40". But for bitmask operators, comma is used for
conjunction in a way that does not really make much sense. Use always
explicit logical operators (&& and ||) to connect bitmask operators.
Thanks to Matt Corallo for the bugreport.
Add support to set or read outgoing MPLS labels using filters. Currently
this supports the addition of one label per route for the first next hop.
Minor changes by committer.
BIRD uses hacked LinuxDocTools for building documentation, keeping some
parts locally and using remaining parts from system-installed one. This
setup breaks when LinuxDocTools makes some internal changes and is hard
to keep consistent.
Just include full LinuxDocTools code (both hacked and unmodified parts)
to avoid consistency issues. Note that we still need some binaries from
LinuxDocTools, so it still needs to be installed to build documentation.
