This is a backport cherry-pick of commits
165156beebcce974e8ea
from the v3.0 branch as we need symbol hashes directly inside their
scopes for more general usage than before.
The redefinable keywords must be specified in any .Y file as follows:
toksym: THE_KEYWORD ;
For whatever reason, parser allocated a symbol for every parsed keyword
in each scope. That wasted time and memory. The effect is worsened with
recent changes allowing local scopes, so keywords often promote soft
scopes (with no symbols) to real scopes.
Do not allocate a symbol for a keyword. Take care of keywords that could
be promoted to symbols (kw_sym) and do it explicitly.
Some of these new BGP role keywords use generic names that collides with
user-defined symbols. Allow them to be redefined. Also remove duplicit
keyword definition for 'prefer'.
The effective keepalive time now scales relative to the negotiated
hold time, to maintain proportion between the keepalive time and the
hold time. This avoids issues when both keepalive and hold times
were configured, the hold time was negotiated to a smaller value,
but the keepalive time stayed the same.
Add new options 'min hold time' and 'min keepalive time', which reject
session attempts with too small hold time.
Improve validation of config options an their documentation.
Thanks to Alexander Zubkov and Sergei Goriunov for suggestions.
Add BGP channel option 'next hop prefer global' that modifies BGP
recursive next hop resolution to use global next hop IPv6 address instead
of link-local next hop IPv6 address for immediate next hop of received
routes.
Implement BGP roles as described in RFC 9234. It is a mechanism for
route leak prevention and automatic route filtering based on common BGP
topology relationships. It defines role capability (controlled by 'local
role' option) and OTC route attribute, which is used for automatic route
filtering and leak detection.
Minor changes done by commiter.
Implement flowspec validation procedure as described in RFC 8955 sec. 6
and RFC 9117. The Validation procedure enforces that only routers in the
forwarding path for a network can originate flowspec rules for that
network.
The patch adds new mechanism for tracking inter-table dependencies, which
is necessary as the flowspec validation depends on IP routes, and flowspec
rules must be revalidated when best IP routes change.
The validation procedure is disabled by default and requires that
relevant IP table uses trie, as it uses interval queries for subnets.
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
The option is not implemented since transition to 2.0 and no plan to add it.
Also remove some deprecated RTS_* valus from documentation.
Thanks to Sébastien Parisot for notification.
Merge multiple BFD option blocks in BGP configs instead of using the last
one. That is necessary for proper handling of templates when BFD options
are used both in a BGP template and in a BGP protocol derived from that
template.
BFD session options are configured per interface in BFD protocol. This
patch allows to specify them also per-request in protocols requesting
sessions (currently limited to BGP).
This is optional check described in RFC 4271. Although this can be also
done by filters, it is widely implemented option in BGP implementations.
Thanks to Eugene Bogomazov for the original patch.
The patch implements optional internal export table to a channel and
hooks it to BGP so it can be used as Adj-RIB-Out. When enabled, all
exported (post-filtered) routes are stored there. An export table can be
examined using e.g. 'show route export table bgp1.ipv4'.
Support for dynamically spawning BGP protocols for incoming connections.
Use 'neighbor range' to specify range of valid neighbor addresses, then
incoming connections from these addresses spawn new BGP instances.
Allow to specify just 'internal' or 'external' for remote neighbor
instead of specific ASN. In the second case that means BGP peers with
any non-local ASNs are accepted.
Extend 'next hop keep' and 'next hop self' options to have boolean values
(enabled / disabled) and also values 'ibgp'/ 'ebgp' to restrict it to
routes received from IBGP / EBGP. This allows to have it enabled by
default in some cases, matches features of other implementations, and
allows to handle some strange cases like EBGP border router with 'next
hop self' also doing IBGP route reflecting.
Change default of 'next hop keep' to enabled for route servers, and
'ibgp' for route reflectors.
Update documentation for these options.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
Covers IPv4/VPNv4 routes with IPv6 next hop (RFC 5549), IPv6 routes with
IPv4 next hop (RFC 4798) and VPNv6 routes with IPv4 next hop (RFC 4659).
Unfortunately it also makes next hop hooks more messy.
Each BGP channel now could have two IGP tables, one for IPv4 next hops,
the other for IPv6 next hops.
Basic support for SAFI 4 and 128 (MPLS labeled IP and VPN) for IPv4 and
IPv6. Should work for route reflector, but does not properly handle
originating routes with next hop self.
Based on patches from Jan Matejka.
Add support for large communities (draft-ietf-idr-large-community),
96bit alternative to RFC 1997 communities.
Thanks to Matt Griswold for the original patch.
Add code for manipulation with TCP-MD5 keys in the IPsec SA/SP database
at FreeBSD systems. Now, BGP MD5 authentication (RFC 2385) keys are
handled automatically on both Linux and FreeBSD.
Based on patches from Pavel Tvrdik.
The patch adds support for channels, structures connecting protocols and
tables and handling most interactions between them. The documentation is
missing yet.
