Implement OSPFv2 (RFC 3623) and OSPFv3 (RFC 5187) graceful restart,
for both restarting and helper sides. Graceful restart is initiated
by 'graceful down' command.
When 'graceful down' command is entered, protocols are shut down
with regard to graceful restart. Namely Kernel protocol does
not remove routes and BGP protocol does not send notification,
just closes the connection.
Useful for implementation of agents implementing the SNMP-BGP MIB, which
requires the local AS of a session to be specified.
Thanks to Jan-Philipp Litza for the patch.
Support for dynamically spawning BGP protocols for incoming connections.
Use 'neighbor range' to specify range of valid neighbor addresses, then
incoming connections from these addresses spawn new BGP instances.
When BGP connection is opened, it may happen that rx hook (with remote
OPEN) is called before tx hook (for local OPEN). Therefore, we need to do
internal changes (like setting local_caps) synchronously with OPENSENT
transition and we need to ensure that OPEN is sent before KEEPALIVE.
Allow to specify just 'internal' or 'external' for remote neighbor
instead of specific ASN. In the second case that means BGP peers with
any non-local ASNs are accepted.
The temporary atttributes are no longer removed by ea_do_prune(), but
they are undefined by store_tmp_attrs() protocol hooks. This fixes
several bugs where temporary attributes were removed when they should
not or not removed when they should be. The flag EAF_TEMP is no longer
needed and was removed.
Update all protocol make_tmp_attrs() / store_tmp_attrs() hooks to use
helper functions and to handle unset attributes properly.
Also fix some related bugs like improper handling of empty eattr list.
Keep track of whether OSPF tmpattrs are actually defined for given route
(using flags in rte->pflags). That makes them behave more like real
eattrs so a protocol can define just a subset of them or they can be
undefined by filters.
Do not set ospf_metric2 for other than type 2 external OSPF routes and do
not set ospf_tag for non-external OSPF routes. That also fixes a bug
where internal/inter-area route propagated from one OSPF instance to
another is initiated with infinity ospf_metric2.
Thanks to Yaroslav Dronskii for the bugreport.
When area is reconfigured to a different type, we need to flush LSAs as
they may not be valid (e.g. NSSA-LSA for non-NSSA area). Also, when we
have have just one OSPF area and that changes type, we could restart OSPF
as there is no state to keep anyway. That solves issue with different
handling of external routes exported to OSPF based of main area type.
External LSAs originated by OSPF routers with VPN-PE behavior enabled are
marked by DN flag and they are ignored by other OSPF routers with VPN-PE
enabled.
Direct acknowledgements should be send as unicast to a corresponding
neighbor. Only delayed acks should be send as multicast to all/designated
routers.
Master may free last DBDES packet immediately. Slave must wait dead
interval before freeing last DBDES packet and then reject duplicate
DBDES packets with SeqNumberMismatch.
Since v2 we have multiple listening BGP sockets, and each BGP protocol
has associated one of them. Use listening socket that accepted the
incoming connection as a key in the dispatch process so only BGP
protocols assocaited with that listening socket can be selected.
This is necesary for proper dispatch when VRFs are used.
This protocol is highly experimental and nobody should use it in
production. Anyway it may help you getting some insight into what eats
so much time in filter processing.
In some circumstances (old LSA flushed but not acknowledged and not
removed) origination of a new LSA may wrongly triggers LSA collision
code. The patch fixes that.
Thanks to Asbjorn Mikkelsen for the bugreport and @mdelagueronniere
for the original patch.
Extend 'next hop keep' and 'next hop self' options to have boolean values
(enabled / disabled) and also values 'ibgp'/ 'ebgp' to restrict it to
routes received from IBGP / EBGP. This allows to have it enabled by
default in some cases, matches features of other implementations, and
allows to handle some strange cases like EBGP border router with 'next
hop self' also doing IBGP route reflecting.
Change default of 'next hop keep' to enabled for route servers, and
'ibgp' for route reflectors.
Update documentation for these options.
When route is exported to regular EBGP, local ASN should be prepended to
AS_PATH. When route is propagated by route server (between RS-marked
EBGP peers), it should not change AS_PATH. Question is what to do in
other cases (from non-RS EBGP, IBGP, or locally originated to RS EBGP).
In 1.6.x, we did not prepend ASN in non-RS EBGP or IBGP to RS EBGP, but
we prepended in local to RS EBGP.
In 2.0.x, we changed that so only RS-EBGP to RS-EBGP is not prepended.
We received some negative responses (thanks to heisenbug and Alexander
Zubkov), we decided to change it back. One reason is that it is simple
to modify the AS_PATH by filters, but not possible to un-modify
changes done by BGP itself. Also, as 1.6.x behavior was not really
consistent, the final behavior is that ASN is never prepended when
exported to RS EBGP, like to IBGP.
Note that i do not express an opinion about whether such configurations
are even reasonable.
The patch implements optional internal import table to a channel and
hooks it to BGP so it can be used as Adj-RIB-In. When enabled, all
received (pre-filtered) routes are stored there and import filters can
be re-evaluated without explicit route refresh. An import table can be
examined using e.g. 'show route import table bgp1.ipv4'.
When a new channel is found during reconfiguration, do force restart
of the protocol, like with any other un-reconfigurable change.
The old behavior was that the new channel was added but remained in down
state, even if the protocol was up, so a manual protocol restart was
often necessary.
In the future this should be improved such that a reconfigurable
channel addition (e.g. direct) is accepted and channel is started,
while an un-reconfigurable addition forces protocol restart.
Fix crash during reconfiguration of OSPF config with vlinks. When vlink
is reconfigured, a generic iface-reconfiguration code is used, which in
one place supposes that it is running on a regular iface.
Thanks to Cybertinus for a bugreport.
Once upon a time, far far away, there were the old Bird developers
discussing what direction of route flow shall be called import and
export. They decided to say "import to protocol" and "export to table"
when speaking about a protocol. When speaking about a table, they
spoke about "importing to table" and "exporting to protocol".
The latter terminology was adopted in configuration, then also the
bird CLI in commit ea2ae6dd0 started to use it (in year 2009). Now
it's 2018 and the terminology is the latter. Import is from protocol to
table, export is from table to protocol. Anyway, there was still an
import_control hook which executed right before route export.
One thing is funny. There are two commits in April 1999 with just two
minutes between them. The older announces the final settlement
on config terminology, the newer uses the other definition. Let's see
their commit messages as the git-log tool shows them (the newer first):
commit 9e0e485e50
Author: Martin Mares <mj@ucw.cz>
Date: Mon Apr 5 20:17:59 1999 +0000
Added some new protocol hooks (look at the comments for better explanation):
make_tmp_attrs Convert inline attributes to ea_list
store_tmp_attrs Convert ea_list to inline attributes
import_control Pre-import decisions
commit 5056c559c4
Author: Martin Mares <mj@ucw.cz>
Date: Mon Apr 5 20:15:31 1999 +0000
Changed syntax of attaching filters to protocols to hopefully the final
version:
EXPORT <filter-spec> for outbound routes (i.e., those announced
by BIRD to the rest of the world).
IMPORT <filter-spec> for inbound routes (i.e., those imported
by BIRD from the rest of the world).
where <filter-spec> is one of:
ALL pass all routes
NONE drop all routes
FILTER <name> use named filter
FILTER { <filter> } use explicitly defined filter
For all protocols, the default is IMPORT ALL, EXPORT NONE. This includes
the kernel protocol, so that you need to add EXPORT ALL to get the previous
configuration of kernel syncer (as usually, see doc/bird.conf.example for
a bird.conf example :)).
Let's say RIP to this almost 19-years-old inconsistency. For now, if you
import a route, it is always from protocol to table. If you export a
route, it is always from table to protocol.
And they lived happily ever after.
Modify protocols to use preferred address change notification instead on
depending on hard-reset of interfaces in that case, and remove hard-reset
in that case. This avoids issue when e.g. IPv6 protocol restarts
interface when IPv4 preferred address changed (as hard-reset is
unavoidable and common for whole iface).
The patch also fixes a bug when removing last address does not send
preferred address change notification.
The new MRT protocol is responsible for periodic RIB table dumps in the
MRT format (RFC 6396). Also the existing code for BGP4MP MRT dumps is
refactored and splitted between BGP to MRT protocols, will be more
integrated into MRT in the future.
Example:
protocol mrt {
table "*";
filename "%N_%F_%T.mrt";
period 60;
}
It is partially based on the old MRT code from Pavel Tvrdik.
Missing argument in MTU change trace message can crash bird when MTU
change happens and trace messages are active.
Thanks to Alexander Velkov for the bugreport.
no more warnings
No more warnings over me
And while it is being compiled all the log is black and white
Release BIRD now and then let it flee
(use the melody of well-known Oh Freedom!)
