The BSD code did not propagate the OS-level IFF_MULTICAST flag to the
Bird-internal IF_MULTICAST flag, which causes problems with Wireguard
interfaces on FreeBSD. The Linux sysdep code does propagate the flag
already, so just copy over the same check and flag update.
For logging purposes a stack allocated net_addr struct was passed by
value as vararg (instead of the expected pointer). This resulted in
a segfault when the specific error condition got logged.
From now, there are no auxiliary pointers stored in the free slab nodes.
This led to strange debugging problems if use-after-free happened in
slab-allocated structures, especially if the structure's first member is
a next pointer.
This also reduces the memory needed by 1 pointer per allocated object.
OTOH, we now rely on pages being aligned to their size's multiple, which
is quite common anyway.
In general, events are code handling some some condition, which is
scheduled when such condition happened and executed independently from
I/O loop. Work-events are a subgroup of events that are scheduled
repeatedly until some (often significant) work is done (e.g. feeding
routes to protocol). All scheduled events are executed during each
I/O loop iteration.
Separate work-events from regular events to a separate queue and
rate limit their execution to a fixed number per I/O loop iteration.
That should prevent excess latency when many work-events are
scheduled at one time (e.g. simultaneous reload of many BGP sessions).
This is an implementation of draft-walton-bgp-hostname-capability-02.
It is implemented since quite some time for FRR and in datacenter, this
gives a nice output to avoid using IP addresses.
It is disabled by default. The hostname is retrieved from uname(2) and
can be overriden with "hostname" option. The domain name is never set
nor displayed.
Minor changes by committer.
With net.ipv4.conf.XXX.ignore_routes_with_linkdown sysctl, a user can
ensure the kernel does not use a route whose target interface is down.
Such route is marked with a 'dead' / RTNH_F_DEAD flag.
Ignore these routes or multipath nexthops during scan.
Thanks to Vincent Bernat for the original patch.
So one can define kernel protocol template without channels.
For other protocols, it is either irrelevant or already done.
Thanks to Clemens Schrimpe for the bugreport.
For ECMP routes, RTA_FLOW attribute must be set per-nexthop, not
per-route. Our corresponding krt_realm attribute is per-route.
Thanks to Mikhail Petrov for the bugreport.
The log subsystem should be locked earlier, as default_log_list() may
internally manipulate with the current_log_list (if it is also a default
log list).
The static logging structures are reused, we need to reinitialize them
otherwise add_tail() would fail in debug build. Reinitializing these
structures should be fine as the list they belong to is being
reinitialized on entry to the very same function.
Thanks to Andreas Rammhold and Mikael Magnusson for patches.
Add support for RTA_MULTIPATH attribute parsing for AF_MPLS routes.
BIRD is capable of installing a multipath route into kernel on Linux,
but it would not be seen because parsing fails. This made BIRD attempt
to install the same route repeatedly.
(The patch minorly updated by committer)
This is a quick workaround for an issue where configured logfiles are
opened/created during parsing of a config file even when parse-and-exit
option is active. We should later refactor the logging code to avoid
opening log during parsing altogether.
When dynamic BGP with remote range is configured, MD5SIG needs to use
newer socket option (TCP_MD5SIG_EXT) to specify remote addres range for
listening socket.
Thanks to Adam Kułagowski for the suggestion.
The old code stored route verdicts and temporary routes directly in
rtable. The new code do not store received routes (it immediately
compares them with exported routes and resolves conflicts) and uses
internal bitmap to keep track of which routes were received and which
needs to be reinstalled.
By not putting 'invalid' temporary routes to rtable, we keep rtable
in consistent state, therefore scan no longer needs to be atomic
operation and could be splitted to multiple events.
Use a hierarchical bitmap in a routing table to assign ids to routes, and
then use bitmaps (indexed by route id) in channels to keep track whether
routes were exported. This avoids unreliable and inefficient re-evaluation
of filters for old routes in order to determine whether they were exported.
Accept RTA_VIA attribute in all cases. The old code always used
RTA_GATEWAY for IPv4 / IPv6 and RTA_VIA for MPLS. The new code uses
RTA_VIA in cases where AF of network and AF of nexthop differs.
Names read from texfiles in /etc/iproute2/* are normalized by replacing
non-alphanumeric chars with underscore. The patch fixes handling of
uppercase letters, which were handled as non-alphanumberic.
Thanks to Igor Gavrilov for the bugreport.
The C11 specification allows only sig_atomic_t and _Atomic variable
access. All other accesses to global variables are undefined behavior.
Using int was probably OK on x86 and x86_64; yet there were some reports
from other architectures (especially some MIPS) that in rare cases,
after issuing SIGHUP, BIRD did strange things.
The command initiating planned graceful restart including bird shutdown
should be called 'graceful restart' instead of 'graceful down', as the
later should be reserved for graceful shutdown in style of RFC 8326.
Use route replace netlink op instead of delete+add netlink ops for kernel
IPv4 route replace. This avoids some packetloss during route replace.
Still use the old behavior for IPv6, as some kernel bugs are hidden in
IPv6 ECMP handling.
