This is a major change of how the filters are interpreted. If everything
works how it should, it should not affect you unless you are hacking the
filters themselves.
Anyway, this change should make a huge improvement in the filter performance
as previous benchmarks showed that our major problem lies in the
recursion itself.
There are also some changes in nest and protocols, related mostly to
spreading const declarations throughout the whole BIRD and also to
refactored dynamic attribute definitions. The need of these came up
during the whole work and it is too difficult to split out these
not-so-related changes.
When area is reconfigured to a different type, we need to flush LSAs as
they may not be valid (e.g. NSSA-LSA for non-NSSA area). Also, when we
have have just one OSPF area and that changes type, we could restart OSPF
as there is no state to keep anyway. That solves issue with different
handling of external routes exported to OSPF based of main area type.
External LSAs originated by OSPF routers with VPN-PE behavior enabled are
marked by DN flag and they are ignored by other OSPF routers with VPN-PE
enabled.
Direct acknowledgements should be send as unicast to a corresponding
neighbor. Only delayed acks should be send as multicast to all/designated
routers.
Master may free last DBDES packet immediately. Slave must wait dead
interval before freeing last DBDES packet and then reject duplicate
DBDES packets with SeqNumberMismatch.
In some circumstances (old LSA flushed but not acknowledged and not
removed) origination of a new LSA may wrongly triggers LSA collision
code. The patch fixes that.
Thanks to Asbjorn Mikkelsen for the bugreport and @mdelagueronniere
for the original patch.
Fix crash during reconfiguration of OSPF config with vlinks. When vlink
is reconfigured, a generic iface-reconfiguration code is used, which in
one place supposes that it is running on a regular iface.
Thanks to Cybertinus for a bugreport.
Once upon a time, far far away, there were the old Bird developers
discussing what direction of route flow shall be called import and
export. They decided to say "import to protocol" and "export to table"
when speaking about a protocol. When speaking about a table, they
spoke about "importing to table" and "exporting to protocol".
The latter terminology was adopted in configuration, then also the
bird CLI in commit ea2ae6dd0 started to use it (in year 2009). Now
it's 2018 and the terminology is the latter. Import is from protocol to
table, export is from table to protocol. Anyway, there was still an
import_control hook which executed right before route export.
One thing is funny. There are two commits in April 1999 with just two
minutes between them. The older announces the final settlement
on config terminology, the newer uses the other definition. Let's see
their commit messages as the git-log tool shows them (the newer first):
commit 9e0e485e50
Author: Martin Mares <mj@ucw.cz>
Date: Mon Apr 5 20:17:59 1999 +0000
Added some new protocol hooks (look at the comments for better explanation):
make_tmp_attrs Convert inline attributes to ea_list
store_tmp_attrs Convert ea_list to inline attributes
import_control Pre-import decisions
commit 5056c559c4
Author: Martin Mares <mj@ucw.cz>
Date: Mon Apr 5 20:15:31 1999 +0000
Changed syntax of attaching filters to protocols to hopefully the final
version:
EXPORT <filter-spec> for outbound routes (i.e., those announced
by BIRD to the rest of the world).
IMPORT <filter-spec> for inbound routes (i.e., those imported
by BIRD from the rest of the world).
where <filter-spec> is one of:
ALL pass all routes
NONE drop all routes
FILTER <name> use named filter
FILTER { <filter> } use explicitly defined filter
For all protocols, the default is IMPORT ALL, EXPORT NONE. This includes
the kernel protocol, so that you need to add EXPORT ALL to get the previous
configuration of kernel syncer (as usually, see doc/bird.conf.example for
a bird.conf example :)).
Let's say RIP to this almost 19-years-old inconsistency. For now, if you
import a route, it is always from protocol to table. If you export a
route, it is always from table to protocol.
And they lived happily ever after.
Missing argument in MTU change trace message can crash bird when MTU
change happens and trace messages are active.
Thanks to Alexander Velkov for the bugreport.
no more warnings
No more warnings over me
And while it is being compiled all the log is black and white
Release BIRD now and then let it flee
(use the melody of well-known Oh Freedom!)
This is a fundamental change of an original (1999) concept of route
processing inside BIRD. During import/export, there was a temporary
ea_list created which was to be used instead of the another one inside
the route itself.
This led to some confusion, quirks, and strange filter code that handled
extended route attributes. Dropping it now.
The protocol interface has changed in an uniform way -- the
`struct ea_list *attrs` argument has been removed from store_tmp_attrs(),
import_control(), rt_notify() and get_route_info().
During route export, the receiving protocol often initialized route
metrics to default value in its import_control hook before export filter
was executed. This is inconsistent with the expectation that an export
filter would process the same route as one in the routing table and it
breaks setting these metrics before (e.g. for static routes directly in
static protocol).
The patch removes the initialization of route metrics in import_control
hook, the default values are already handled in rt_notify hook called
after export filters.
The patch also changed the behavior of OSPF to keep metrics when a route
is reannounced between OSPF instances (to be consistent with other
protocols) and the behavior when both ospf_metric1 and ospf_metric2
are specified (to have more expected behavior).
The old timer interface is still kept, but implemented by new timers. The
plan is to switch from the old inteface to the new interface, then clean
it up.
The TTL check must be done after instance ID dispatch to avoid warnings
when a physical iface is shared by multiple instances and some use TTL
security and some not.
In such case, next hop has to be taken from Link-LSA like in broadcast
case, not from neighbor source address like in other PtP cases.
Also add some checks, comments and code cleanup.
OSPFv3-AF can handle multiple topologies of diferent address families
(IPv4, IPv6, both unicast and multicast) using separate instances
distinguished by instance ID ranges.
Add basic VRF (virtual routing and forwarding) support. Protocols can be
associated with VRFs, such protocols will be restricted to interfaces
assigned to the VRF (as reported by Linux kernel) and will use sockets
bound to the VRF. E.g., different multihop BGP instances can use diffent
kernel routing tables to handle BGP TCP connections.
The VRF support is preliminary, currently there are several limitations:
- Recent Linux kernels (4.11) do not handle correctly sockets bound
to interaces that are part of VRF, so most protocols other than multihop
BGP do not work. This will be fixed by future kernel versions.
- Neighbor cache ignores VRFs. Breaks config with the same prefix on
local interfaces in different VRFs. Not much problem as single hop
protocols do not work anyways.
- Olock code ignores VRFs. Breaks config with multiple BGP peers with the
same IP address in different VRFs.
- Incoming BGP connections are not dispatched according to VRFs.
Breaks config with multiple BGP peers with the same IP address in
different VRFs. Perhaps we would need some kernel API to read VRF of
incoming connection? Or probably use multiple listening sockets in
int-new branch.
- We should handle master VRF interface up/down events and perhaps
disable associated protocols when VRF goes down. Or at least disable
associated interfaces.
- Also we should check if the master iface is really VRF iface and
not some other kind of master iface.
- BFD session request dispatch should be aware of VRFs.
- Perhaps kernel protocol should read default kernel table ID from VRF
iface so it is not necessary to configure it.
- Perhaps we should have per-VRF default table.
Dropped struct mpnh and mpnh_*()
Now struct nexthop exists, nexthop_*(), and also included struct nexthop
into struct rta.
Also converted RTD_DEVICE and RTD_ROUTER to RTD_UNICAST. If it is needed
to distinguish between these two cases, RTD_DEVICE is equivalent to
IPA_ZERO(a->nh.gw), RTD_ROUTER is then IPA_NONZERO(a->nh.gw).
From now on, we also explicitely want C99 compatible compiler. We assume
that this 20-year norm should be known almost everywhere.
The variable nfa is not cleaned before each loop iteration and can have
a wrong value of nfa.nhs_reuse from the previous step.
Thanks to Bernardo Figueiredo for the bugreport and analysis.
Stubnet nodes in OSPF FIB were removed during rt_sync(), but the pointer
remained in top_hash_entry.nf, so net-summary LSA origination was
confused, reported 'LSA ID collision' and net-summary LSAs were not
originated properly.
Thanks to Naveen Chowdary Yerramneni for bugreport and analysis.
- Unit Testing Framework (BirdTest)
- Integration of BirdTest into the BIRD build system
- Tests for several BIRD modules
Based on squashed Pavel Tvrdik's int-test branch, updated for
current int-new branch.
Also removed the lib-dir merging with sysdep. Updated #include's
accordingly.
Fixed make doc on recent Debian together with moving generated doc into
objdir.
Moved Makefile.in into root dir
Retired all.o and birdlib.a
Linking the final binaries directly from all the .o files.
Many protocols do almost the same when creating a rte_update request
before calling rte_update2(). This commit should simplify the protocol
side of the route-creation routine.
After restart, LSAs locally originated by the previous instance are
received from neighbors. They are installed to LSA db and flushed. If
export of a route triggers origination of a new external LSA before flush
of the received one is complete, the check in ospf_originate_lsa() causes
origination to fail (because en->nf is NULL for the old LSA and non-NULL
for the new LSA). The patch fixes this by updating the en->nf for LSAs
being flushed (as is already done for empty ones). Generally, en->nf
field deserves some better description in the code.
Thanks to Jigar Mehta for analyzing the problem.
The patch adds support for channels, structures connecting protocols and
tables and handling most interactions between them. The documentation is
missing yet.
Explicit setting of AF_INET(6|) in IP socket creation. BFD set to listen
on v6, without setting the V6ONLY flag to catch both v4 and v6 traffic.
Squashing and minor changes by Ondrej Santiago Zajicek
New data types net_addr and variants (in lib/net.h) describing
network addresses (prefix/pxlen). Modifications of FIB structures
to handle these data types and changing everything to use these
data types instead of prefix/pxlen pairs where possible.
The commit is WiP, some protocols are not yet updated (BGP, Kernel),
and the code contains some temporary scaffolding.
Comments are welcome.
The new RIP implementation fixes plenty of old bugs and also adds support
for many new features: ECMP support, link state support, BFD support,
configurable split horizon and more. Most options are now per-interface.
The patch adds suport for specifying route attributes together with
static routes, e.g.:
route 10.1.1.0/24 via 10.0.0.1 { krt_advmss = 1200; ospf_metric1 = 100; };
New LSA checksumming code separates generic Fletcher-16 and OSPF-specific
code and avoids back and forth endianity conversions, making it much more
readable and also several times faster.
Prior to this patch, BIRD validates the OSPF LSA checksum by calculating
a new checksum and comparing it with the checksum in the header. Due to
the specifics of the Fletcher checksum used in OSPF, this is not
necessarily correct as the checkbytes in the header may be calculated via
a different means and end up with a different value that is nonetheless
still correct.
The documented means of validating the checksum as specified in RFC 905
B.4 is to calculate c0 and c1 from the unchanged contents of the packet,
which must result in a zero value to be considered valid.
Thanks to Chris Boot for the patch.
Fixes cases where the same network or external route are propagated by
several OSPF routes and some other corner cases in next hop construction
and ECMP. Allows to specify whether external routes should be merged.
Thanks to Peter Christensen for the original patch.
I/O:
- BSD: specify src addr on IP sockets by IP_HDRINCL
- BSD: specify src addr on UDP sockets by IP_SENDSRCADDR
- Linux: specify src addr on IP/UDP sockets by IP_PKTINFO
- IPv6: specify src addr on IP/UDP sockets by IPV6_PKTINFO
- Alternative SKF_BIND flag for binding to IP address
- Allows IP/UDP sockets without tx_hook, on these
sockets a packet is discarded when TX queue is full
- Use consistently SOL_ for socket layer values.
OSPF:
- Packet src addr is always explicitly set
- Support for secondary addresses in BSD
- Dynamic RX/TX buffers
- Fixes some minor buffer overruns
- Interface option 'tx length'
- Names for vlink pseudoifaces (vlinkX)
- Vlinks use separate socket for TX
- Vlinks do not use fixed associated iface
- Fixes TTL for direct unicast packets
- Fixes DONTROUTE for OSPF sockets
- Use ifa->ifname instead of ifa->iface->name
Interfaces for OSPF and RIP could be configured to use (and request)
TTL 255 for traffic to direct neighbors.
Thanks to Simon Dickhoven for the original patch for RIPng.
Implements support for IPv6 traffic class, sets higher priority for OSPF
and RIP outgoing packets by default and allows to configure ToS/DS/TClass
IP header field and the local priority of outgoing packets.
BIRD used zero netmask in hello packets on all PtP links, not just on
unnumbered ones. This patch fixes it and adds option 'ptp netmask'
for overriding the default behavior.
Thanks to Alexander V. Chernikov for the original patch.
Configured NBMA neighbors in OSPFv3 should be link-local addresses, old
behavior was to silently ignore global ones. The patch allows BIRD to
accept global ones, but adds a warning and a documentation notice.
Thanks to Wilco Baan Hofman for the bugreport.
Router ID could be automatically determined based of subset of
ifaces/addresses specified by 'router id from' option. The patch also
does some minor changes related to router ID reconfiguration.
Thanks to Alexander V. Chernikov for most of the work.
Although it is a slight deviation from the standard, it has no ill
consequences for OSPFv2 and the change fixes a compatibility issue
with some broken implementations.
Allows to send and receive multiple routes for one network by one BGP
session. Also contains necessary core changes to support this (routing
tables accepting several routes for one network from one protocol).
It needs some more cleanup before merging to the master branch.
