Now sk_open() requires an explicit IO loop to open the socket in. Also
specific functions for socket RX pause / resume are added to allow for
BGP corking.
And last but not least, socket reloop is now synchronous to resolve
weird cases of the target loop stopping before actually picking up the
relooped socket. Now the caller must ensure that both loops are locked
while relooping, and this way all sockets always have their respective
loop.
If there are lots of loops in a single thread and only some of the loops
are actually active, the other loops are now kept aside and not checked
until they actually get some timers, events or active sockets.
This should help with extreme loads like 100k tables and protocols.
Also ping and loop pickup mechanism was allowing subtle race
conditions. Now properly handling collisions between loop ping and pickup.
Repeated pipe refeed should not end route refresh as the prune routine
may start pruning otherwise valid routes.
The same applies for BGP repeated route refresh.
When changing default table behavior, I missed that it enabled to
configure multiple master4 and master6 tables. Now BIRD recognizes it
and fails properly.
The import table feed wasn't resetting the table-specific route values
like REF_FILTERED and thus made the route look like filtered even though
it should have been re-evaluated as accepted.
This brought unnecessary complexity into the decision procedures while the
performance aspects weren't worth it. It just saved one ea_list traversal
when many others are also done.
The change 371eb49043 introduced early free
of old_config. Unfortunately, it did not properly check whether it is not
still in use (blocked by obstacle during reconfiguration). Fix that.
It also means that we still could have a short peak when three configs
are in use (when a new reconfig is requeste while the previous one is
still active).
Missing translation from BGP attribute ID to eattr ID in bgp_unset_attr()
broke automatic removal of bgp_med during export to EBGP peers.
Thanks to Edward Sun for the bugreport.
The feature of showing all prefixes inside the given one has been added
in v2.0.9 but not well documented. Fixing it by this update.
Text in doc and commit message added by commiter.
Even though the free bind option is primarily meant to alleviate problems
with addresses assigned too late, it's also possible to use BIRD with AnyIP
configuration, assigning whole ranges to the machine. Therefore free bind
allows also to create an outbound connection from specific address even though
such address is not assigned.
and "%M" formats expect "Input/output error" message but musl returns
"I/O error". Proposed change compares the printf output with string
returned from strerror function for EIO constant.
See-also: https://bugs.gentoo.org/836713
Minor change from committer.
When a linpool is used to allocate a one-off big load of memory, it
makes no sense to keep that amount of memory for future use inside the
linpool. Contrary to previous implementations where the memory was
directly free()d, we now use the page allocator which has an internal
cache which keeps the released pages for us and subsequent allocations
simply get these released pages back.
And even if the page cleanup routine kicks in inbetween, the pages get
only madvise()d, not munmap()ed so performance aspects are negligible.
This may fix some memory usage peaks in extreme cases.
The change 371eb49043 introduced early free
of old_config. Unfortunately, it did not properly check whether it is not
still in use (blocked by obstacle during reconfiguration). Fix that.
It also means that we still could have a short peak when three configs
are in use (when a new reconfig is requeste while the previous one is
still active).
The babel protocol normally sends all its messages as multicast packets,
but the protocol specification allows most messages to be sent as either
unicast or multicast, and the two can be mixed freely. In particular, the
babeld implementation can be configured to unicast updates to all peers
instead of sending them as unicast.
Daniel discovered that this can cause problems with the packet counter
checks in the MAC extension due to packet reordering. This happens on WiFi
networks where clients have power save enabled (which is quite common in
infrastructure networks): in this case, the access point will buffer all
multicast traffic and only send it out along with its beacons, leading to a
maximum buffering in default Linux-based access point configuration of up
to 200 ms.
This means that a Babel sender that mixes unicast and multicast messages
can have the unicast messages overtake the multicast messages because of
this buffering; when authentication is enabled, this causes the receiver to
discard the multicast message when it does arrive because it now has a
packet counter value less than the unicast message that arrived before it.
Daniel observed that this happens frequently enough that Babel ceases to
work entirely when runner over a WiFi network.
The issue has been described in draft-ietf-babel-mac-relaxed, which is
currently pending RFC publication. That also describes two mitigation
mechanisms: Keeping separate PC counters for unicast and multicast, and
using a reorder window for PC values. This patch implements the former as
that is the simplest, and resolves the particular issue seen on WiFi.
Thanks to Daniel Gröber for the bugreport.
Minor changes from committer.
The patch implements an IPv4 via IPv6 extension (RFC 9229) to the Babel
routing protocol (RFC 8966) that allows annoncing routes to an IPv4
prefix with an IPv6 next hop, which makes it possible for IPv4 traffic
to flow through interfaces that have not been assigned an IPv4 address.
The implementation is compatible with the current Babeld version.
Thanks to Toke Høiland-Jørgensen for early review on this work.
Minor changes from committer.
Instead of propagating interface updates as they are loaded from kernel,
they are enqueued and all the notifications are called from a
protocol-specific event. This change allows to break the locking loop
between protocols and interfaces.
Anyway, this change is based on v2 branch to keep the changes between v2
and v3 smaller.
The interface list must be flushed when device protocol is stopped. This
was done in a hardcoded specific hook inside generic protocol routines.
The cleanup hook was originally used for table reference counting late
cleanup, yet it can be also simply used for prettier interface list flush.
