BFD requires defined local IP, but for nexthop with onlink there might
not be such address. So we reject this combination of nexthop options.
This prevent crash where such combination of options is used.
Allow to define both nexthop and interface using iproute2-like syntax,
e.g.: route 10.0.0.0/16 via 10.1.0.1 dev "eth0";
Now we can avoid to use link-local scope hack (e.g. 10.1.0.1%eth0)
for cases where both nexthop and interface have to be defined.
Thanks to Marcin Saklak for the suggestion.
Some [redacted] (yes, myself) had a really bad idea
to rename nest/route.h to nest/rt.h while refactoring
some data structures out of it.
This led to unnecessarily complex problems with
merging updates from v2. Reverting this change
to make my life a bit easier.
At least it needed only one find-sed command:
find -name '*.[chlY]' -type f -exec sed -i 's#nest/rt.h#nest/route.h#' '{}' +
Conflicts:
conf/cf-lex.l
conf/conf.h
conf/confbase.Y
conf/gen_keywords.m4
conf/gen_parser.m4
filter/config.Y
nest/config.Y
proto/bgp/config.Y
proto/static/config.Y
Keywords and attributes are split to separate namespaces, to avoid
collisions between regular keyword use and attribute overlay.
Old configs do not define MPLS domains and may use a static protocol
to define static MPLS routes.
When MPLS channel is the only channel of static protocol, handle it
as a main channel. Also, define implicit MPLS domain if needed and
none is defined.
Instead of just using route attributes, static routes with
static MPLS labels can be defined just by e.g.:
route 10.1.1.0/24 mpls 100 via 10.1.2.1 mpls 200;
When MPLS is active, static IP/VPN routes are automatically labeled
according to active label policy and corresponding MPLS routes are
automatically generated.
Add a new protocol offering route aggregation.
User can specify list of route attributes in the configuration file and
run route aggregation on the export side of the pipe protocol. Routes are
sorted and for every group of equivalent routes new route is created and
exported to the routing table. It is also possible to specify filter
which will run for every route before aggregation.
Furthermore, it will be possible to set attributes of new routes
according to attributes of the aggregated routes.
This is a work in progress.
Original work by Igor Putovny, subsequent cleanups and finalization by
Maria Matejka.
For now, there are 4 phases: Necessary (device), Connector (kernel, pipe), Generator (static, rpki) and Regular.
Started and reconfigured are from Necessary to Regular, shutdown backwards.
This way, kernel can flush routes before actually being shutdown.
Instead of propagating interface updates as they are loaded from kernel,
they are enqueued and all the notifications are called from a
protocol-specific event. This change allows to break the locking loop
between protocols and interfaces.
Anyway, this change is based on v2 branch to keep the changes between v2
and v3 smaller.
There were some confusion about validity and usage of pflags, which
caused incorrect usage after some flags from (now removed) protocol-
specific area were moved to pflags.
We state that pflags:
- Are secondary data used by protocol-specific hooks
- Can be changed on an existing route (in contrast to copy-on-write
for primary data)
- Are irrelevant for propagation (not propagated when changed)
- Are specific to a routing table (not propagated by pipe)
The patch did these fixes:
- Do not compare pflags in rte_same(), as they may keep cached values
like BGP_REF_STALE, causing spurious propagation.
- Initialize pflags to zero in rte_get_temp(), avoid initialization in
protocol code, fixing at least two forgotten initializations (krt
and one case in babel).
- Improve documentation about pflags
When f_line is done, we have to pop the stack frame. The old code just
removed nominal number of args/vars. Change it to use stored ventry value
modified by number of returned values. This allows to allocate variables
on a stack frame during execution of f_lines instead of just at start.
But we need to know the number of returned values for a f_line. It is 1
for term, 0 for cmd. Store that to f_line during linearization.
There were quite a lot of conflicts in flowspec validation code which
ultimately led to some code being a bit rewritten, not only adapted from
this or that branch, yet it is still in a limit of a merge.
